Nissan Titan A60. Manual — part 713
MA-32
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
REMOVAL
1. Remove engine room cover using power tool. Refer to
EM-24, "Removal and Installation"
.
2. Remove ignition coil. Refer to
EM-38, "Removal and Installation"
.
3. Remove spark plug using suitable tool.
CAUTION:
Do not shock ignition coil.
CAUTION:
Do not drop or shock spark plug.
INSPECTION AFTER REMOVAL
• Do not use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be used.
• Checking and adjusting plug gap is not required between change
intervals.
INSTALLATION
Installation is in the reverse order of removal.
Spark Plug Types
* : Always check with the Parts Department for the latest parts information.
CAUTION:
Do not drop or shock spark plug.
SEM294A
Cleaner air pressure:
Less than 588 kPa (5.9 bar, 6 kg/cm
2
, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C
SMA806CA
Make
NGK
Model
Standard model
FFV model
Standard type*
DILFR5A-11
DILFR5A-11D
Gap (Nominal)
1.1 mm (0.043 in)
1.1 mm (0.043)
ENGINE MAINTENANCE
MA-33
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
Checking EVAP Vapor Line
INFOID:0000000006158430
1. Visually inspect the EVAP vapor lines for improper attachment, cracks, damage, loose connections, chaf-
ing, or deterioration.
2. Inspect the vacuum relief valve of the fuel tank filler cap for clogging and sticking. Refer to
MA-34
< PERIODIC MAINTENANCE >
CHASSIS AND BODY MAINTENANCE
CHASSIS AND BODY MAINTENANCE
IN-CABIN MICROFILTER
IN-CABIN MICROFILTER : Removal and Installation
INFOID:0000000006751642
REPLACEMENT PROCEDURE
1. Remove the two lower glove box hinge pins to remove the glove
box from the instrument panel and let it hang from the cord.
2. Remove the screw and remove the in-cabin microfilter cover.
3. Remove the in-cabin microfilters from the heater and cooling
unit assembly housing.
4. Insert the first new in-cabin microfilter into the heater and cool-
ing unit assembly housing and slide it over to the right. Insert the
second new in-cabin microfilter into the heater and cooling unit
assembly housing.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
5. Install the in-cabin microfilter cover.
WLIA0027E
LJIA0134E
LJIA0148E
LJIA0134E
CHASSIS AND BODY MAINTENANCE
MA-35
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
6. Install the lower glove box in the instrument panel and secure it
with the two hinge pins.
EXHAUST SYSTEM
EXHAUST SYSTEM : Checking Exhaust System
INFOID:0000000006158432
Check exhaust pipes, muffler and mounting for improper attachment, leaks, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
A/T FLUID
A/T FLUID : Checking the A/T Fluid (ATF)
INFOID:0000000006751644
CAUTION:
If using the vehicle for towing, the A/T fluid must be replaced as specified. Refer to
NORTH AMERICA : Introduction of Periodic Maintenance"
(United States and Canada),
MEXICO : Introduction of Periodic Maintenance"
(Mexico).
1. Before driving, the A/T fluid level can be checked at A/T fluid
temperatures of 30
° to 50° C (86° to 122° F) using the “COLD”
range on the A/T fluid level gauge as follows:
a. Park the vehicle on a level surface and set the parking brake.
b. Start the engine and move the selector lever through each gear
position. Shift the selector lever into the “P” position.
c. Check the A/T fluid level with the engine idling.
d. Remove the A/T fluid level gauge and wipe it clean with a lint-
free paper.
CAUTION:
When wiping the A/T fluid from the A/T fluid level gauge,
always use a lint-free paper, not a cloth.
WLIA0027E
SMA211A
LLIA0071E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст