Nissan Titan A60. Manual — part 953
TM-200
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
14. Remove O-ring from A/T assembly harness connector.
15. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
16. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
17. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
Installation
CAUTION:
After completing installation, check A/T fluid leakage and fluid level. Refer to
.
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
CONTROL VALVE WITH TCM
TM-201
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1. Connect TCM connector (1) and transmission range switch con-
nector (2).
2. Install A/T assembly harness connector to control valve with
TCM.
3. Connect TCM connector.
4. Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
JSDIA1313ZZ
TM-202
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
6. Install plug (2) to bracket(1).
7. Install plug (1) [with bracket (2)] to control valve with TCM.
•
:Bolt
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
8. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
JSDIA1312ZZ
JSDIA1311ZZ
1
: Brake band
JSDIA1318ZZ
SCIA5142E
CONTROL VALVE WITH TCM
TM-203
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
9. Install bolts (A), (B) and (C) in control valve with TCM.
10. Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (1
→ 2 → 3). Then tighten other
bolts.
11. Tighten control valve with TCM bolts to the specified torque.
12. Connect output speed sensor connector (1).
13. Securely fasten output speed sensor (1) harness with terminal
clip (
).
14. Install oil pan to transmission case. Refer to
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (km-g, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
JSDIA1319ZZ
JSDIA1316ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст