Nissan Titan A60. Manual — part 954
TM-204
< REMOVAL AND INSTALLATION >
CONTROL VALVE WITH TCM
15. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
16. Install snap ring to A/T assembly harness connector.
17. Connect A/T assembly harness connector.
18. Connect the negative battery terminal.
19. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
TM-168, "Checking the A/T Fluid (ATF)"
.
SCIA5038E
SCIA5039E
REAR OIL SEAL
TM-205
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
Rear Oil Seal
INFOID:0000000006159458
REMOVAL AND INSTALLATION
Removal
1. Remove rear propeller shaft. Refer to
DLN-141, "Removal and Installation"
2. Remove transfer from transmission (4WD models). Refer to
TM-208, "Removal and Installation (4WD)"
.
3. Remove rear oil seal using suitable tool.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
Installation
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
"Removal and Installation (4WD)"
.
3. Install rear propeller shaft. Refer to
.
4. Check the A/T fluid level and for fluid leakage. Refer to
"Checking the A/T Fluid (ATF)"
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
TM-206
< UNIT REMOVAL AND INSTALLATION >
TRANSMISSION ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Removal and Installation (2WD)
INFOID:0000000006736259
COMPONENTS
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1. Disconnect the battery negative terminal. Refer to
PG-76, "Removal and Installation"
2. Remove A/T fluid indicator.
3. Remove engine under cover using power tool.
1.
A/T fluid indicator pipe
2.
A/T fluid indicator
3.
O-ring
4.
Transmission assembly
5.
Fluid cooler tube
6.
A/T cross member
7.
Insulator
8.
Copper washers
AWDIA0553GB
TRANSMISSION ASSEMBLY
TM-207
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4. Remove crankshaft position sensor (POS) from A/T assembly.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or foreign material to get on the
sensor front edge magnetic area.
• Do not place in an area affected by magnetism.
5. Remove A/T fluid indicator pipe.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
6. Remove exhaust front tube and center muffler using power tool.
EX-5, "Removal and Installation"
7. Remove rear propeller shaft. Refer to
DLN-150, "Removal and Installation"
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
8. Disconnect control cable.
9. Remove A/T fluid cooler tubes from A/T assembly.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
10. Support A/T assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
11. Remove dust cover from converter housing.
12. Turn crankshaft to access and remove the four bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
13. Remove air breather hose. Refer to
.
14. Disconnect A/T assembly harness connector.
15. Remove the A/T assembly to engine bolts using power tool.
16. Remove A/T assembly from vehicle using transmission jack.
CAUTION:
• Secure torque converter to prevent it from dropping.
• Secure A/T assembly to a transmission jack.
INSPECTION
Installation and Inspection of Torque Converter
LCIA0334E
LCIA0335E
SCIA0499E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст