Nissan Titan A60. Manual — part 288
TRANSFER FLUID
DLN-91
< PERIODIC MAINTENANCE >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PERIODIC MAINTENANCE
TRANSFER FLUID
Replacement
INFOID:0000000006179500
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
NORTH AMERICA : Introduction of Periodic Maintenance"
(United States and Canada) ,
MEXICO : Introduction of Periodic Maintenance"
(Mexico).
DRAINING
1. Stop engine.
2. Remove the drain plug and gasket and drain the fluid.
3. Install the drain plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
FILLING
1. Remove the filler plug and gasket.
2. Fill the transfer with new fluid until the fluid level reaches the
specified limit near the filler plug hole.
CAUTION:
Carefully fill fluid. (Fill up for approx. 3 minutes.)
3. Leave the vehicle for 3 minutes, and check fluid level again.
4. Install the filler plug with a new gasket to the transfer. Tighten to the specified torque. Refer to
.
CAUTION:
Do not reuse gasket.
Inspection
INFOID:0000000006179501
CAUTION:
If using the vehicle for towing, the transfer fluid must be replaced as specified. Refer to
NORTH AMERICA : Introduction of Periodic Maintenance"
FLUID LEAKAGE AND FLUID LEVEL
1. Make sure that fluid is not leaking from the transfer assembly or around it.
SDIA3286E
Fluid grade and capacity : Refer to
NORTH AMERICA : Fluids
and Lubricants"
(United
States),
(Mexico).
SDIA3287E
DLN-92
< PERIODIC MAINTENANCE >
[TRANSFER: TX15B]
TRANSFER FLUID
2. Check fluid level from the filler plug hole as shown.
CAUTION:
Do not start engine while checking fluid level.
3. Install the filler plug with a new gasket to the transfer. Tighten to
the specified torque. Refer to
CAUTION:
Do not reuse gasket.
SDIA3287E
TRANSFER CONTROL UNIT
DLN-93
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
TRANSFER CONTROL UNIT
Removal and Installation
INFOID:0000000006179502
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
CAUTION:
When removing transfer control unit, transfer state must be at 2WD.
2. Turn the ignition switch OFF and disconnect negative battery terminal.
3. Remove the lower instrument panel RH. Refer to
IP-16, "Removal and Installation"
4. Disconnect the two transfer control unit connectors.
5. Remove the transfer control unit bolts.
6. Remove the transfer control unit.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the transfer control unit, tighten bolts to the specified torque.
• After the installation, check 4WD shift indicator pattern. If NG, adjust position between transfer assembly and
transfer control unit. Refer to
DLN-84, "Precaution for Transfer Assembly and Transfer Control Unit Replace-
.
BDIA0014E
Transfer control unit bolts : 5.1 N·m (0.52 kg-m, 45 in-lb)
DLN-94
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
FRONT OIL SEAL
FRONT OIL SEAL
Removal and Installation
INFOID:0000000006179503
REMOVAL
1. Partially drain the transfer fluid. Refer to
.
2. Remove the front propeller shaft. Refer to
DLN-132, "Removal and Installation"
.
3. Remove the companion flange self-lock nut using suitable tool.
4. Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
5. Remove the companion flange using suitable tool.
6. Remove the front oil seal from the front case using Tool.
CAUTION:
Do not damage front case.
INSTALLATION
LDIA0142E
SDIA2779E
WDIA0193E
Tool number
: ST33290001 (J-34286)
LDIA0144E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст