Nissan Titan A60. Manual — part 289
FRONT OIL SEAL
DLN-95
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1. Install the new front oil seal until it is flush with the end face of
the front case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3. Install the new self-lock nut and tighten to the specified torque
using suitable tool. Refer to
CAUTION:
Do not reuse self-lock nut.
4. Install the front propeller shaft. Refer to
.
5. Refill the transfer with fluid and check for fluid leakage and fluid
Tool number
: KV38100500 ( — )
LDIA0145E
SDIA2214E
LDIA0147E
DLN-96
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
REAR OIL SEAL
REAR OIL SEAL
Removal and Installation
INFOID:0000000006179504
REMOVAL
1. Partially drain the transfer fluid. Refer to
.
2. Remove the rear propeller shaft. Refer to
DLN-141, "Removal and Installation"
3. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
4. Remove oil cover from dust cover.
5. Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the oil cover until it reaches the end face of the new dust cover.
3. Apply petroleum jelly to the circumference of the new dust cover
(1). Position the new dust cover as shown.
CAUTION:
• Do not reuse dust cover.
• Position the protrusions at the position shown.
• 2: Rear case assembly
• A: Protrusions
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: KV38100500 ( — )
LDIA0140E
AWDIA0550GB
REAR OIL SEAL
DLN-97
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4. Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
5. Install the rear propeller shaft. Refer to Refer to
(3S1410).
6. Refill the transfer with fluid and check for fluid leakage and fluid
Tool number
: KV40105310 ( — )
PDIA0116E
DLN-98
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
TRANSFER CONTROL DEVICE
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000006179505
REMOVAL
1. Switch the 4WD shift switch to 2WD and set the transfer assembly to 2WD.
2. Disconnect the transfer control device connector.
3. Remove the breather hose from the transfer control device.
4. Remove the bolts and detach the transfer control device.
INSTALLATION
1. Install the new O-ring to the transfer control device.
CAUTION:
• Do not reuse O-ring.
• Apply petroleum jelly to O-ring.
2. Install the transfer control device.
a. Turn the control shift rod fully counterclockwise using a flat-
bladed screwdriver, and then put a mark on the control shift rod.
b. Align the transfer control device shaft cutout with the mark on
the control shift rod, and install.
NOTE:
Turn the transfer control device when the transfer control device
connection does not match.
LDIA0136E
SDIA3378E
PDIA0119E
PDIA0120E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст