Nissan Titan A60. Manual — part 488
HEADLAMP
EXL-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYSTEM DESCRIPTION
HEADLAMP
System Diagram
INFOID:0000000006178983
System Description
INFOID:0000000006178984
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
and turn signal switch). When the combination switch (lighting and turn signal switch) is placed in the 2nd posi-
tion, the BCM (body control module) receives input requesting the headlamps and park lamps to illuminate.
This input is communicated to the IPDM E/R (intelligent power distribution module engine room) via the CAN
communication lines. The CPU (central processing unit) of the IPDM E/R controls the headlamp LH high,
headlamp RH high and headlamp low relay coils. When energized, these relays direct power to the respective
headlamps, which then illuminate.
Component Parts Location
INFOID:0000000006178985
Component Description
INFOID:0000000006178986
LOW BEAM OPERATION
AWLIA1715GB
1.
BCM M18, M20 (view with instrument
panel removed)
2.
IPDM E/R E122, E123, E124
3.
Combination switch (lighting and turn-
signal switch) M28
4.
Combination meter M24
ALLIA0379ZZ
EXL-8
< SYSTEM DESCRIPTION >
HEADLAMP
When the combination switch (lighting and turn signal switch) is in 2ND position, the BCM receives input
requesting the headlamps to illuminate. This input is communicated to the IPDM E/R via the CAN communica-
tion lines. The CPU of the IPDM E/R controls the headlamp low relay coil which supplies power to the low
beam headlamps.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION
With the combination switch (lighting and turn signal switch) in the 2ND position and placed in HIGH position,
the BCM receives input requesting the headlamp high beams to illuminate. The flash to pass feature can be
used any time and also sends a signal to the BCM. This input is communicated to the IPDM E/R via the CAN
communication lines. The CPU of the combination meter controls the ON/OFF status off the HIGH BEAM indi-
cator. The CPU of the IPDM E/R controls the headlamp LH high relay coil and RH high relay coil which supply
power to the high beam headlamps.
The combination meter receives a high beam request signal (ON) via the CAN communication lines and turns
the high beam indicator lamp ON.
EXTERIOR LAMP BATTERY SAVER CONTROL
With the combination switch (lighting and turn signal switch) in the 2ND position and the ignition switch is
turned from ON or ACC to OFF, the battery saver feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes unless the lighting switch position is
changed. If the lighting switch position is changed, then the headlamps are turned off.
This setting can be changed by CONSULT-III. Refer to
AUTO LIGHT SYSTEM
EXL-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
AUTO LIGHT SYSTEM
System Diagram
INFOID:0000000006178987
System Description
INFOID:0000000006178988
• BCM (Body Control Module) controls auto light operation according to signals from optical sensor, combina-
tion switch (lighting and turn signal switch) and ignition switch.
• IPDM E/R (Intelligent Power Distribution Module Engine Room) operates parking, license plate, tail and
headlamps according to CAN communication signals from BCM.
• Optical sensor detects ambient brightness of 800 to 2,500 lux. And optical sensor converts light (lux) to volt-
age, then sends the optical sensor signal to BCM.
OUTLINE
The auto light control system has an optical sensor that detects outside brightness.
When the combination switch (lighting and turn signal switch) is in AUTO position, it automatically turns ON/
OFF the parking, license plate, tail and headlamps in accordance with the ambient light. Sensitivity can be
adjusted in four steps. For the details of the setting, Refer to
EXL-27, "HEADLAMP : CONSULT-III Function
ABLIA2793GB
EXL-10
< SYSTEM DESCRIPTION >
AUTO LIGHT SYSTEM
Component Parts Location
INFOID:0000000006178989
Component Description
INFOID:0000000006178990
AUTO LIGHT OPERATION
The auto light system operates the low beam and high beam headlamps, parking lamps, tail lamps and license
plate lamps. The BCM monitors the combination switch (lighting and turn signal switch) position as a part of
the BCM combination switch reading function. When the combination switch (lighting and turn signal switch) is
in the AUTO position, the BCM automatically turns the lamps ON/OFF according to ambient light brightness.
NOTE:
Timing for when lamps turn ON/OFF can be changed by the function setting of CONSULT-III. Refer to
"HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)"
.
1.
BCM M18, M19, M20 (view with instru-
ment panel removed)
2.
IPDM E/R E122, E123, E124
3.
Optical sensor M302
4.
Front door switch (crew cab)
LH B8
RH B108
5.
Rear door switch (crew cab)
LH B18
RH B116
6.
Front door switch (king cab)
LH B8
RH B108
7.
Rear door switch upper (king cab)
LH B73
RH B156
8.
Rear door switch lower (king cab)
LH B74
RH B157
9.
Combination switch (lighting and turn
signal switch) M28
ALLIA0563GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст