Nissan Titan A60. Manual — part 866
PREPARATION
SR-3
< PREPARATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006163315
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-42057-UPD)
Air bag key set
Part of kit (J-42057)
Removing and installing air bag lock
LRS210
SR-4
< REMOVAL AND INSTALLATION >
DRIVER AIR BAG MODULE
REMOVAL AND INSTALLATION
DRIVER AIR BAG MODULE
Removal and Installation
INFOID:0000000006163316
REMOVAL
CAUTION:
• Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a driver
air bag direct-connect harness connector is damaged, the spiral cable must be replaced.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove the left and right side bolts.
3. Lift the driver air bag module from the steering wheel.
4. Disconnect the air bag harness and horn connectors, then remove the driver air bag module.
• For removal/installation of the direct-connect SRS connectors, refer to
.
CAUTION:
• When servicing the SRS, do not work from directly in front of air bag module.
• Always place air bag module with pad side facing upward.
• Do not insert any foreign objects (screwdriver, etc.) into air
bag module or harness connectors.
• Do not disassemble air bag module.
• Do not use old bolts after removal; replace with new bolts.
• Do not expose the air bag module to temperatures exceeding
90
°C (194°F).
1.
Horn harness
2.
Steering wheel hook
3.
Inflator harness
4.
Side lids RH/LH
5.
Driver air bag module
6.
Steering wheel
WHIA0159E
LHIA0052E
DRIVER AIR BAG MODULE
SR-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the air bag module if it has been dropped or sus-
tained an impact.
• Do not allow oil, grease or water to come in contact with the
air bag module.
INSTALLATION
Installation is in the reverse order of removal.
• If driver air bag module is being replaced due to deployment, spiral cable must also be replaced. Refer to
SR-6, "Removal and Installation"
.
• For removal/installation of the direct-connect SRS connectors, refer to
SRC-9, "Direct-connect SRS Compo-
• After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SBF814E
SR-6
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
SPIRAL CABLE
Removal and Installation
INFOID:0000000006163317
REMOVAL
CAUTION:
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals and wait at
least three minutes.
• When servicing the SRS, do not work from directly in front of air bag module.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
2. Remove the steering wheel. Refer to
ST-11, "Removal and Installation"
.
3. Remove the instrument lower panel RH. Refer to
IP-17, "Removal and Installation"
4. Remove the column cover upper and lower.
5. Remove wiper washer switch connector, then pinch the tabs at
wiper and washer switch base and slide switch away from steer-
ing column to remove.
AWHIA0141GB
1.
Steering wheel
2.
Lighting and turn signal switch
3.
Wiper and washer switch
4.
Spiral cable
5.
Driver air bag module connector
6.
Column cover upper
7.
Column assembly
8.
Column cover lower
9.
Screw (Do not remove)
10. Screw
A.
LHIA0034E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст