Nissan Titan A60. Manual — part 865
SN-28
< UNIT REMOVAL AND INSTALLATION >
SONAR CONTROL UNIT
SONAR CONTROL UNIT
Removal and Installation
INFOID:0000000006159223
REMOVAL
1. Remove the rear panel. Refer to
INT-14, "Removal and Installation"
.
2. For king cab models only, pull up the carpet to gain access to
the sonar control unit.
3. Disconnect the sonar control unit connector.
• Sonar control unit (king cab) (1)
• Sonar control unit (crew cab) (2)
4. Remove the two bolts and remove the sonar control unit.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1106GB
SN
BUZZER
SN-29
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BUZZER
Removal and Installation
INFOID:0000000006159224
REMOVAL
1. Remove the combination meter cover. Refer to
IP-13, "Removal and Installation"
2. Remove the two bolts (1), disconnect the connector (2) and
remove the front buzzer.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0425ZZ
SR-1
RESTRAINTS
C
D
E
F
G
I
J
K
L
M
SECTION
SR
A
B
SR
N
O
P
CONTENTS
SRS AIRBAG
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for SRS "AIR BAG" and "SEAT BELT
PRE-TENSIONER" Service . . . . . . . . . ..
Occupant Classification System Precaution . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
REMOVAL AND INSTALLATION . . . .
DRIVER AIR BAG MODULE . . . . . . . ...
Removal and Installation . . . . . . . . . . ...
SPIRAL CABLE . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
FRONT PASSENGER AIR BAG MODULE . .
Removal and Installation . . . . . . . . . . ..
SIDE CURTAIN AIR BAG MODULE . . . .
Removal and Installation . . . . . . . . . . .
CRASH ZONE SENSOR . . . . . . . . ...
Removal and Installation . . . . . . . . . . .
SIDE AIR BAG (SATELLITE) SENSOR . . ...
Removal and Installation . . . . . . . . . . .
FRONT SEAT BELT PRE-TENSIONER . . ...
Removal and Installation . . . . . . . . . . .
DIAGNOSIS SENSOR UNIT . . . . . . . .
Removal and Installation . . . . . . . . . . .
OCCUPANT CLASSIFICATION SYSTEM
CONTROL UNIT . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COLLISION DIAGNOSIS . . . . . . . . ..
For Frontal Collision . . . . . . . . . . . .
SR-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006163312
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for SRS "AIR BAG" and "SEAT BELT PRE-TENSIONER" Service
INFOID:0000000006163313
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bags and seat belt
pre-tensioners to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.
• The air bag diagnosis sensor unit must always be installed with the arrow mark “
⇐” pointing toward the front
of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or rust
before installation and replace as required.
• The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
turn steering wheel or column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
Occupant Classification System Precaution
INFOID:0000000006163314
Replace occupant classification system control unit and passenger front seat cushion as an assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст