Nissan Titan A60. Manual — part 969
TM-264
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
15. Install seal rings to drum support.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Install snap ring in transmission case while compressing return
spring using Tool.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
18. Install revers brake drive plates driven plates and dish plates in transmission case.
CAUTION:
SCIA3333E
SCIA2324E
Tool number
: KV31102400 (J-34285 and J-34285-87)
SCIA5877E
ASSEMBLY
TM-265
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Take care with order of plates.
• Snap ring (1)
• Retaining plate (2)
• Drive plate (3)
• Driven plate (4)
• Dish plate (5)
• Drive plate/Driven plate: 7/7
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
22. Measure clearance (A) between retaining plate and snap ring. If
not within specified clearance, select proper retaining plate.
WCIA0625E
SCIA5249E
SCIA2439E
Clearance “A”
: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate
: Refer to
.
SCIA3129E
TM-266
< UNIT DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-221, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
24. Install output speed sensor (1) to transmission case and tighten
bolt (
) to specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
25. As shown in the figure, use the drift to drive rear oil seal into the
rear extension (2WD models) (A) or adapter case (4WD models)
(B) until it is flush.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
26. Install return spring (1) to parking pawl (2).
SCIA5031E
Output speed sensor bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)
JSDIA1321ZZ
1
: Drift [ST33400001 (J-26082)]
2
: Drift [Commercial service tool Ø64 mm (2.52 in)]
JSDIA1914ZZ
SCIA6180J
ASSEMBLY
TM-267
< UNIT DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
SCIA3424E
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст