Nissan Titan A60. Manual — part 146
BRAKE TUBE AND HOSE
BR-11
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE TUBE AND HOSE
Hydraulic Circuit
INFOID:0000000006163274
VDC/TCS/ABS - Four Channel Hydraulic System
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning the steering wheel both clockwise
and counterclockwise.
• The brake piping is an important safety part. If a brake fluid leak is detected, always disassemble the
parts. Replace applicable part with a new one, if necessary.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover connections so that no dirt, dust, or other foreign matter gets in.
• Refill with new specified brake fluid. Refer to
MA-21, "FOR NORTH AMERICA : Fluids and Lubri-
MA-22, "FOR MEXICO : Fluids and Lubricants"
(Mexico).
• Do not reuse drained brake fluid.
FRONT BRAKE
FRONT BRAKE : Inspection
INFOID:0000000006163275
INSPECTION AFTER REMOVAL
CAUTION:
AWFIA0427ZZ
1.
Actuator
2.
Master cylinder
3.
Brake booster
4.
Connector
5.
Axle mounted connector
9.3 N·m (0.95 kg-m, 82 in-lb)
A.
Union bolt (front caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
B.
Flare nut M12
18.2 N·m (1.9 kg-m, 13 ft-lb)
C.
Flare nut M10
13.0 N·m (1.3 kg-m, 10 ft-lb)
D.
Hose connection (rear caliper)
18.2 N·m (1.9 kg-m, 13 ft-lb)
E.
Flare nut to rear hose
16.2 N·m (1.7 kg-m, 12 ft-lb)
BR-12
< BASIC INSPECTION >
BRAKE TUBE AND HOSE
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
REAR BRAKE
REAR BRAKE : Inspection
INFOID:0000000006163276
INSPECTION AFTER REMOVAL
CAUTION:
Brake tubes and hoses are important safety parts. Always disassemble the parts and retighten their fit-
tings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part is
detected.
1. Check brake lines (tubes and hoses) and connections for fluid leaks, damage, twists, deformation, contact
with other parts, and loose connections. Replace any parts as necessary. Refer to
2. While depressing brake pedal under a force of 785 N (80 kg-f, 177 lb-f) with engine running for approxi-
mately 5 seconds, check each part for fluid leaks.
BRAKE PEDAL
BR-13
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PERIODIC MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment - Standard Pedal
INFOID:0000000006163277
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool
at a 90
° angle to the floor as shown.
2. Adjust the brake pedal height to specifications.
Brake Pedal Specifications
Unit: mm (in)
ADJUSTMENT
1. Loosen the stop lamp switch and ASCD cancel switch (if equipped) by turning 45
° counterclockwise.
Tool number :
—
(J-46532)
AWFIA0557ZZ
Free height (H)
Pedal full stroke (S)
Clearance between brake pedal bracket and threaded end of stop lamp switch
(C1) and ASCD cancel switch [if equipped] (C
2
)
BR-14
< PERIODIC MAINTENANCE >
BRAKE PEDAL
2. Loosen lock nut (A) on the input rod, then turn input rod to adjust
the brake pedal to specified height. When finished adjusting,
tighten lock nut (A) to specification.
CAUTION:
Make sure that the screw portion of the end of input rod is
located inside the clevis.
3. With the brake pedal pulled up and held by hand, press the stop
lamp switch and the ASCD cancel switch (if equipped) in until
threaded ends contact the brake pedal bracket.
4. With the threaded ends of the stop lamp switch and ASCD can-
cel switch (if equipped) contacting the pedal bracket, turn the
switches 45
° clockwise to lock in place. Check that the stop
lamp switch and ASCD cancel switch (if equipped) threaded end
to brake pedal bracket gap (C) is within specifications.
CAUTION:
Make sure that the gap (C) between the brake pedal bracket
and stop lamp switch and ASCD cancel switch (if equipped)
threaded ends are within specification.
5. Check the brake pedal for smooth operation.
CAUTION:
Make sure that the stop lamp goes off when the brake pedal
is released.
Inspection and Adjustment - Adjustable Pedal
INFOID:0000000006163278
INSPECTION
1. Inspect the brake pedal free height (H) from the floor using Tool at a 90
° angle to the floor as shown.
CAUTION:
When equipped with adjustable pedal, the pedal must be in
the forward most (closest to the floor) position for pedal
height measurement.
2. Adjust the height referring to the following specifications.
Brake Pedal Specifications
Unit: mm (in)
Lock nut (A)
:Refer to
PFIA0436E
Tool number :
—
(J-46532)
ALFIA0149ZZ
Pedal free height (H) with pedal in forward most position
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст