Nissan Titan A60. Manual — part 262
DLK-122
< REMOVAL AND INSTALLATION >
DOOR
DOOR
Fitting Adjustment
INFOID:0000000006179267
KING CAB
AWKIA1728GB
E.
4.5
± 1.0 mm (0.177 ± 0.039 in)
F.
6.5
± 1.0 mm (0.256 ± 0.039 in)
DOOR
DLK-123
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CREW CAB
Front Door
Longitudinal clearance and surface height adjustment at front end
1. Remove the front fender. Refer to
EXT-22, "Removal and Installation"
.
2. Loosen the hinge bolts. Raise the front door at rear end to adjust.
3. Install the front fender. Refer to
EXT-22, "Removal and Installation"
Rear Door Crew Cab
Longitudinal clearance and surface height adjustment at rear end
1. Remove the center pillar upper garnish. Refer to
INT-14, "Removal and Installation"
.
2. Accessing from inside the vehicle, loosen the nuts. Open the rear door, and raise the rear door at rear end
to adjust. Tighten the nuts to specification.
3. Install the center pillar upper garnish. Refer to
INT-14, "Removal and Installation"
.
Rear Door King Cab
Longitudinal clearance and surface height adjustment at front end
1. With the door open, support and loosen the hinge to door nuts.
2. Adjust the door position as necessary.
3. Tighten the nuts to specification.
AWKIA1730GB
E.
4.5
± 1.0 mm (0.177 ± 0.039 in)
F.
6.5
± 1.0 mm (0.256 ± 0.039 in)
Rear door hinge nuts
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
Rear door hinge nuts
: 24.5 N·m (2.5 kg-m, 18 ft-lb)
DLK-124
< REMOVAL AND INSTALLATION >
DOOR
Striker adjustment
1. Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
Removal and Installation
INFOID:0000000006179268
KING CAB
Front Door
CAUTION:
• When removing and installing the door assembly, support the door with a jack and shop cloth to pro-
tect the door and body.
• When removing and installing door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
1. Remove the front door lock assembly. Refer to
DLK-127, "Removal and Installation"
2. Remove the door harness.
3. Remove the check link cover.
4. Remove the check link bolt from the hinge pillar.
5. Remove the door-side hinge nuts and bolts, and remove the
door assembly.
Installation is in the reverse order of removal.
• Align the front door. Refer to
.
Rear Door
CAUTION:
• When removing and installing the door assembly, support the door with a jack and shop cloth to pro-
tect the door and body.
• When removing and installing door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
LIIA1621E
LIIA1503E
LIIA1727E
DOOR
DLK-125
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Remove the door glass. Refer to
2. Remove the speaker.
3. Remove the door handles and latch assembly. Refer to
DLK-130, "Component Structure"
4. Remove the check link.
5. Remove the wire harness.
6. Remove the door assembly.
Installation is in the reverse order of removal.
• Align the rear door. Refer to
CREW CAB
CAUTION:
• When removing and installing the door assembly, support the door with a jack and shop cloth to pro-
tect the door and body.
• When removing and installing door assembly, be sure to carry out the fitting adjustment.
• Check the hinge rotating part for poor lubrication. If necessary, apply body grease.
1. Remove the rear door lock assembly. Refer to
DLK-131, "Removal and Installation"
2. Remove the door harness.
3. Remove the check link cover.
4. Remove the check link bolt from the hinge pillar.
WIIA0334E
LIIA1503E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст