Nissan Pathfinder (2008 year). Manual — part 464
SQUEAK AND RATTLE TROUBLE DIAGNOSES
INT-5
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Trunk lid striker out of adjustment
3.
The trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2.
Sun visor shaft shaking in the holder
3.
Front or rear windshield touching headliner and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
OVERHEAD CONSOLE (FRONT AND REAR)
Overhead console noises are often caused by the console panel clips not being engaged correctly. Most of
these incidents are repaired by pushing up on the console at the clip locations until the clips engage.
In addition look for:
1.
Loose harness or harness connectors.
2.
Front console map/reading lamp lens loose.
3.
Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
INT-6
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000001686218
LAIA0072E
SQUEAK AND RATTLE TROUBLE DIAGNOSES
INT-7
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LAIA0071E
INT-8
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001686220
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Service Notice
INFOID:0000000001686219
• When removing or installing various parts, place a cloth or padding on the vehicle body to prevent scratches.
• Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to soil or
damage them.
• Apply sealing compound where necessary when installing parts.
• When applying sealing compound, be careful that the sealing compound does not protrude from parts.
• When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust preven-
tion measures.
PREPARATION
INT-9
< PREPARATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000001686221
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000001686222
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle kit
Repairing the cause of noise
SBT839
SBT840
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
INT-10
< ON-VEHICLE REPAIR >
DOOR FINISHER
ON-VEHICLE REPAIR
DOOR FINISHER
Removal and Installation
INFOID:0000000001686223
FRONT DOOR
Removal
1.
Remove the power window switch assembly.
• Disconnect the harness connectors.
2.
Remove the pull handle escutcheon.
3.
Remove the pull handle cover and remove screw.
4.
Lift the armrest upward to release clips and remove armrest.
• Remove the screws behind armrest.
5.
Release the clips and remove the door finisher.
1.
Front door
2.
Mirror bolt cover LH
3.
Pull handle escutcheon
4.
Pull handle/lock lever assembly
5.
Pull handle cover
6.
Front door finisher LH
7.
Seat memory switch (if equipped)
8.
Power window/lock switch assembly 9.
Armrest
10. Front door handle bracket
A.
Clip C101
B.
Clip C205
AWJIA0049GB
DOOR FINISHER
INT-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Disconnect lock cable and handle cable from door handle assembly. Refer to
.
6.
Remove the memory seat switch (if equipped).
• Disconnect the harness connector.
7.
Remove the pull handle/lock lever assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1.
Remove the power window switch assembly.
• Disconnect the harness connector.
2.
Remove the pull handle cover.
• Remove the screw behind the pull handle cover.
3.
Remove the pull handle escutcheon.
4.
Lift upward to release clips and remove the armrest.
• Remove the screws behind armrest.
5.
Release the clips and remove the rear door finisher.
• Disconnect the rear door tweeter connector, then remove the rear door tweeter screws and remove the
rear door tweeter.
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Rear door tweeter
3.
Pull handle/lock lever assembly
4.
Pull handle escutcheon
5.
Pull handle cover
6.
Metal clip
7.
Power window switch assembly
8.
Armrest
9.
Rear door finisher (RH shown)
10. Rear door handle bracket
A.
Clip C101
AWJIA0050GB
INT-12
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
BODY SIDE TRIM
Component
INFOID:0000000001686224
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Access cover (RH side only)
6.
Center pillar lower finisher
7.
Front kick plate
8.
Lower dash side finisher
9.
Front door welt
10. Front pillar lower finisher
11.
Front pillar upper finisher
12.
Front pillar assist grip
13. LH side demister grille
14.
Molded plastic clip
15.
Garnish
C.
Clip C101
D.
Clip C111
E.
Metal clip
⇐
Front
AWJIA0051GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст