Nissan Pathfinder (2008 year). Manual — part 24
AV-32
< ON-VEHICLE REPAIR >
[BASE AUDIO]
AUDIO UNIT
INSTALLATION
Installation is in the reverse order of removal.
AV
FRONT TWEETER
AV-33
< ON-VEHICLE REPAIR >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
FRONT TWEETER
Removal and Installation
INFOID:0000000001315978
REMOVAL
CAUTION:
Use a suitable tool to prevent damage to the front tweeter speaker grille trim and the instrument panel.
1.
Remove the front tweeter grille.
2.
Remove the front tweeter screws (A).
3.
Pull out the front tweeter speaker (1) and disconnect front
tweeter connector, then remove the front tweeter speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0344ZZ
AV-34
< ON-VEHICLE REPAIR >
[BASE AUDIO]
FRONT DOOR SPEAKER
FRONT DOOR SPEAKER
Removal and Installation
INFOID:0000000001315979
REMOVAL
1.
Remove the front door finisher. Refer to
INT-10, "Removal and Installation"
2.
Remove the front door speaker screws (A).
3.
Pull out the front door speaker (1), and disconnect the front door
speaker connector and remove the front door speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0347ZZ
AV
REAR DOOR SPEAKER
AV-35
< ON-VEHICLE REPAIR >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
REAR DOOR SPEAKER
Removal and Installation
INFOID:0000000001315980
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-10, "Removal and Installation"
.
2.
Remove the rear door speaker screws (A).
3.
Disconnect the rear door speaker connector (B) and remove
rear door speaker (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA0348ZZ
AV-36
< ON-VEHICLE REPAIR >
[BASE AUDIO]
AUDIO ANTENNA
AUDIO ANTENNA
Window Antenna Repair
INFOID:0000000001317778
ELEMENT CHECK
1.
Attach probe circuit tester (ohm setting) to antenna terminal on
each side.
• When measuring continuity, wrap tin foil around the top of
probe. Then, press the foil against the wire with your fin-
ger.
2.
If an element is broken, no continuity will exist.
SEL250I
SEL122R
SEL252I
AV
AUDIO ANTENNA
AV-37
< ON-VEHICLE REPAIR >
[BASE AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
3.
To locate a break, move probe along element. Tester indication
will change abruptly when probe passes the broken point.
ELEMENT REPAIR
SEL253I
AV-38
< BASIC INSPECTION >
[MID AUDIO]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000001450765
OVERALL SEQUENCE
DETAILED FLOW
1.
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the
incident/malfunction occurred).
>> GO TO 2
2.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer. Verify relation between the symptom and the condition
when the symptom is detected.
>> GO TO 3
3.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
ALNIA0182GB
AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-39
< BASIC INSPECTION >
[MID AUDIO]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is malfunctioning part detected?
YES
>> GO TO 4
NO
>> GO TO 2
4.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure.
>> GO TO 5
5.
FINAL CHECK
Refer to confirmed symptom in step 2, and make sure that the symptom is not detected.
Has the symptom been repaired?
YES
>> Inspection End.
NO
>> GO TO 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст