Nissan Pathfinder (2008 year). Manual — part 607
TM-198
< ON-VEHICLE REPAIR >
OIL PAN
2.
Install the oil pan (2) with new oil pan gasket with the bolts and
clips (1) finger tight to secure inplace as shown.
•
: Vehicle Front
•
: Oil pan bolts
CAUTION:
• Be sure the oil drain plug is located to the rear of the
transmission assembly.
• Before installing oil pan bolts, remove any traces of old
sealant from the sealing surfaces and threaded holes.
• Do not reuse old gasket, replace with a new one.
• Always replace the oil pan bolts as they are self-sealing.
• Partially install the oil pan bolts in a criss-cross pattern to
prevent dislocation of the gasket.
3.
Tighten oil pan bolts in numerical order as shown.
4.
Refill the A/T with fluid and check for fluid leakage. Refer to
TM-180, "Checking the A/T Fluid (ATF)"
.
AWDIA0023ZZ
Oil pan bolts
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA4113E
CONTROL VALVE WITH TCM
TM-199
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL VALVE WITH TCM
Control Valve with TCM and A/T Fluid Temperature Sensor 2
INFOID:0000000001282978
Exploded view
CONTROL VALVE WITH TCM AND A/T FLUID TEMPRATURE SENSOR 2
Removal
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
.
3.
Disconnect A/T assembly harness connector.
AWDIA0024ZZ
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
A/T fluid temperature sensor 2
7.
Oil pan gasket
8.
Clips
9.
Oil pan bolt
10. Oil pan
11.
Magnet
12. Drain plug
13. Drain plug gasket
14. Terminal cord assembly
15. O-ring
TM-200
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
4.
Remove snap ring from A/T assembly harness connector.
5.
Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6.
Remove oil pan and oil pan gasket. Refer to
TM-197, "Removal and Installation"
.
7.
Straighten the terminal clip to free the terminal cord assembly for
A/T fluid temperature sensor 2 harness.
8.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Do not damage connector.
9.
Straighten terminal clip to free the revolution sensor harness.
10. Disconnect revolution sensor connector.
CAUTION:
Do not damage connector.
SCIA5021E
SCIA5022E
SCIA5446E
SCIA7525E
CONTROL VALVE WITH TCM
TM-201
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11. Remove bolts (A), (B) and (C) from control valve with TCM.
12. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
13. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5142E
SCIA5301E
SCIA5264E
SCIA5155E
TM-202
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
16. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Do not damage connectors.
Installation
CAUTION:
After completing installation, check A/T fluid leakage and fluid level. Refer to
.
1.
Connect TCM connector and park/neutral position switch con-
nector.
SCIA5447E
SCIA5448E
SCIA5449E
SCIA5449E
CONTROL VALVE WITH TCM
TM-203
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2.
Install A/T assembly harness connector to control valve with
TCM.
3.
Connect TCM connector.
4.
Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5.
Install A/T fluid temperature sensor 2 to bracket.
6.
Install A/T fluid temperature sensor 2 (with bracket) to control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
TM-199, "Control Valve with TCM
and A/T Fluid Temperature Sensor 2"
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
SCIA5450E
SCIA5447E
SCIA5155E
SCIA5264E
SCIA5301E
TM-204
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
7.
Install control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor is securely
installed into turbine revolution sensor hole.
• Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
8.
Install bolts (A), (B) and (C) in control valve with TCM.
9.
Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (1
→
2
→
3). Then tighten other
bolts.
10. Tighten control valve with TCM bolts to the specified torque.
TM-199, "Control Valve with TCM and A/T Fluid Tem-
.
SCIA5034E
SCIA5142E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5140E
CONTROL VALVE WITH TCM
TM-205
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clip.
15. Install oil pan to transmission case. Refer to
TM-197, "Removal and Installation"
.
16. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal.
20. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
SCIA5446E
SCIA7525E
SCIA5038E
SCIA5039E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст