Nissan Pathfinder (2008 year). Manual — part 608
TM-206
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
Exploded view
INFOID:0000000001724671
Removal and Installation
INFOID:0000000001724673
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
.
3.
Disconnect A/T assembly harness connector.
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
A/T fluid temperature sensor 2
7.
Oil pan gasket
8.
Clips
9.
Oil pan bolt
10. Oil pan
11.
Magnet
12. Drain plug
13. Drain plug gasket
14. Terminal cord assembly
15. O-ring
AWDIA0024ZZ
CONTROL VALVE WITH TCM
TM-207
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
Remove snap ring from A/T assembly harness connector.
5.
Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6.
Remove oil pan and oil pan gasket. Refer to
TM-197, "Removal and Installation"
.
7.
Straighten the terminal clip to free the terminal cord assembly for
A/T fluid temperature sensor 2 harness.
8.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Do not damage connector.
9.
Straighten terminal clip to free the revolution sensor harness.
10. Disconnect revolution sensor connector.
CAUTION:
Do not damage connector.
SCIA5021E
SCIA5022E
SCIA5446E
SCIA7525E
TM-208
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
11. Remove bolts (A), (B) and (C) from control valve with TCM.
12. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
13. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5142E
SCIA5301E
SCIA5264E
SCIA5155E
CONTROL VALVE WITH TCM
TM-209
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
16. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Do not damage connectors.
Installation
CAUTION:
After completing installation, check A/T fluid leakage and fluid level. Refer to
.
1.
Connect TCM connector and park/neutral position switch con-
nector.
SCIA5447E
SCIA5448E
SCIA5449E
SCIA5449E
TM-210
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
2.
Install A/T assembly harness connector to control valve with
TCM.
3.
Connect TCM connector.
4.
Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5.
Install A/T fluid temperature sensor 2 to bracket.
6.
Install A/T fluid temperature sensor 2 (with bracket) to control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
TM-199, "Control Valve with TCM
and A/T Fluid Temperature Sensor 2"
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
SCIA5450E
SCIA5447E
SCIA5155E
SCIA5264E
SCIA5301E
CONTROL VALVE WITH TCM
TM-211
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Install control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor is securely
installed into turbine revolution sensor hole.
• Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
8.
Install bolts (A), (B) and (C) in control valve with TCM.
9.
Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (1
→
2
→
3). Then tighten other
bolts.
10. Tighten control valve with TCM bolts to the specified torque.
TM-199, "Control Valve with TCM and A/T Fluid Tem-
.
SCIA5034E
SCIA5142E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5140E
TM-212
< ON-VEHICLE REPAIR >
CONTROL VALVE WITH TCM
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clip.
15. Install oil pan to transmission case. Refer to
TM-197, "Removal and Installation"
.
16. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal.
20. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
.
SCIA5446E
SCIA7525E
SCIA5038E
SCIA5039E
REAR OIL SEAL
TM-213
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000001724682
REMOVAL
1.
Remove rear propeller shaft. Refer to
DLN-316, "Removal and Installation"
2.
Remove transfer from transmission (4WD models). Refer to
DLN-148, "Removal and Installation"
(ATX14B),
DLN-287, "Removal and Installation"
(TX15B).
3.
Remove rear oil seal using flat bladed screwdriver.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
INSTALLATION
1.
Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2.
Install transfer to transmission (4WD models). Refer to
148, "Removal and Installation"
(ATX14B),
(TX15B).
3.
Install rear propeller shaft. Refer to
.
4.
Check the A/T fluid level and for fluid leakage. Refer to
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст