Nissan Pathfinder (2008 year). Manual — part 167
HORN FUNCTION
DLK-237
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between IPDM E/R harness connector and
horn relay harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK INTERMITTENT INCIDENT
GI-51, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation of IPDM E/R"
.
NO
>> Repair or replace the malfunctioning part.
WIIA1252E
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
A: E122
45
B: H-1
1
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
E122
45
Ground
No
DLK-238
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMBINATION METER DISPLAY FUNCTION
COMBINATION METER DISPLAY FUNCTION
Description
INFOID:0000000001728533
Displays each operation method guide and warning for system malfunction.
Component Function Check
INFOID:0000000001728534
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Using Consult-III, activate "P-SHIFT" and "KEY" warning lamp indicators in "ACTIVATE TEST" mode.
Do the warning lamps illuminate?
YES
>> Combination meter warning lamp indicators are OK.
NO
>> Refer to
DLK-238, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001728535
1.
CHECK COMBINATION METER
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check combination meter. Refer to
MWI-23, "Diagnosis Description"
.
2.
CHECK INTERMITTENT INCIDENT
GI-51, "Intermittent Incident"
>> INSPECTION END.
WARNING CHIME FUNCTION
DLK-239
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WARNING CHIME FUNCTION
Description
INFOID:0000000001728536
Performs operation method guide and warning with buzzer.
Component Function Check
INFOID:0000000001728537
1.
CHECK FUNCTION
With CONSULT-III
1.
Check the operation with "INSIDE BUZZER" in the Active Test.
2.
Touch “TAKE OUT”, “KNOB”or “KEY” on screen.
Is the inspection result normal?
Yes
>> Warning buzzer into combination meter is OK.
No
>> Refer to
DLK-239, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000001728538
1.
CHECK METER BUZZER CIRCUIT
The inoperative warning chime is contained inside the combination meter. Replace combination meter.
>> Inspection end.
DLK-240
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HAZARD FUNCTION
HAZARD FUNCTION
Description
INFOID:0000000001728539
Perform answer-back for each operation with number of blinks.
Component Function Check
INFOID:0000000001728540
1.
CHECK FUNCTION
Check hazard warning lamp "FLASHER" in ACTIVE TEST.
Is the inspection result normal?
YES
>> Hazard warning lamp circuit is OK.
NO
>> Refer to
DLK-240, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000001728541
1.
CHECK HAZARD SWITCH CIRCUIT
Operate the hazard lights by turning ON the hazard warning switch.
Do the lights operate normally?
YES
>> Replace the BCM. Refer to BCS for replacement and configuration procedure.
NO
>> Repair or replace hazard warning switch circuit. Refer to
KEY SWITCH (BCM INPUT)
DLK-241
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY SWITCH (BCM INPUT)
Diagnosis Procedure
INFOID:0000000001728561
1.
CHECK KEY SWITCH INPUT SIGNAL
With CONSULT-II
Check key switch "KEY ON SW" in DATA MONITOR mode with CONSULT–III. Refer to
LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
• When key is inserted to ignition key cylinder:
• When key is removed from ignition key cylinder:
Without CONSULT-II
Check voltage between BCM connector M18 terminal 37 and
ground.
OK or NG
OK
>> Key switch (insert) circuit is OK.
NG
>> GO TO 2.
2.
CHECK KEY SWITCH (INSERT)
1.
Turn ignition switch OFF.
2.
Disconnect key switch connector.
3.
Check continuity between key switch terminals.
OK or NG
OK
>> Repair or replace harness or fuse.
NG
>> Replace key switch.
KEY ON SW
: ON
KEY ON SW
: OFF
Connec-
tor
Terminal
Condition
Voltage (V)
(+)
(–)
M18
37
Ground
Key is inserted.
Battery voltage
Key is removed.
0
LIIA0567E
Terminals
Condition
Continuity
1 – 2
Key is inserted.
Yes
Key is removed.
No
WIIA0559E
DLK-242
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
HEADLAMP FUNCTION
HEADLAMP FUNCTION
Diagnosis Procedure
INFOID:0000000001728545
1.
CHECK HEADLAMP OPERATION
Do headlamps operate with headlamp switch?
YES or NO
YES
>> Headlamp circuit is OK.
NO
>> Check headlamp circuit. Refer to
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
DLK-243
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
MAP LAMP AND IGNITION KEYHOLE ILLUMINATION FUNCTION
Diagnosis Procedure
INFOID:0000000001728546
1.
CHECK MAP LAMP OPERATION
When room lamp switch is in "DOOR" position, open the driver or passenger door.
Map lamp and ignition keyhole illumination should illuminate.
Is the inspection result normal?
YES
>> Map lamp circuit is OK.
NO
>> Check map lamp circuit. Refer to
.
DLK-244
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITH CONSULT-III
KEYFOB ID SET UP WITH CONSULT-III
ID Code Entry Procedure
INFOID:0000000001728547
KEYFOB ID SET UP WITH CONSULT-III
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-
cific ID code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not
known, all controller ID codes should be erased. After all ID codes are erased, the ID codes of all
remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If
five ID codes are stored in memory when an additional code is registered, only the oldest code is
erased. If less than five codes are stored in memory when an additional code is registered, the new
ID code is added and no ID codes are erased.
• Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID
code will be erased.
• Even if the same ID code that is already in memory is input, the same ID code can be entered. The
code is counted as an additional code.
1.
Turn ignition switch ON.
2.
Select “BCM”.
3.
Select “MULTI REMOTE ENT”.
4.
Select “WORK SUPPORT”.
5.
You can register, erase or confirm a keyfob ID code. To register a new code, select the following option
and follow CONSULT-III instructions:
• “REMO CONT ID REGIST”
Use this mode to register a keyfob ID code.
NOTE:
Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.
• “REMO CONT ID ERASUR”
Use this mode to erase a keyfob ID code.
• “REMO CONT ID CONFIR”
Use this mode to confirm if a keyfob ID code is registered or not.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст