Nissan Pathfinder (2008 year). Manual — part 168
KEYFOB ID SET UP WITHOUT CONSULT-III
DLK-245
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID SET UP WITHOUT CONSULT-III
ID Code Entry Procedure
INFOID:0000000001728548
KEYFOB ID SET UP WITHOUT CONSULT-III
NOTE:
• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A specific ID
code can be erased with CONSULT-III. However, when the ID code of a lost keyfob is not known, all control-
LIIA1670E
DLK-246
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB ID SET UP WITHOUT CONSULT-III
ler ID codes should be erased. After all ID codes are erased, the ID codes of all remaining and/or new key-
fobs must be re-registered.
To erase all ID codes in memory, register one ID code (keyfob) five times. After all ID codes are erased, the
ID codes of all remaining and/or new keyfobs must be re-registered.
• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If five ID
codes are stored in memory, when an additional code is registered, only the oldest code is erased. If less
than five ID codes are stored in memory, when an additional ID code is registered, the new ID code is added
and no ID codes are erased.
• If you need to activate more than two additional new keyfobs, repeat the procedure “Additional ID code
entry” for each new keyfob.
• Entry of maximum five ID codes is allowed. When more than five ID codes are entered, the oldest ID code
will be erased.
• Even if same ID code that is already in the memory is input, the same ID code can be entered. The code is
counted as an additional code.
BACK DOOR HALF SWITCH
DLK-247
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR HALF SWITCH
Diagnosis Procedure
INFOID:0000000001728549
1.
BACK DOOR HALF SWITCH SIGNAL INSPECTION
1.
Turn ignition switch OFF.
2.
While opening and closing the back door, check voltage
between back door control unit connector D509 terminal 7 and
ground.
s the inspection result normal?
YES
>> Switch is OK.
NO
>> GO TO 2.
2.
BACK DOOR HALF SWITCH CIRCUIT INSPECTION
1.
Disconnect back door control unit and back door cinching latch unit connectors.
2.
Check continuity between back door control unit connector (A)
D509 terminal 7 and back door cinching latch unit connector (B)
D502 terminal 6.
3.
Check continuity between back door control unit connector (A)
D509 terminal 7 and ground.
s the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
BACK DOOR HALF SWITCH GROUND INSPECTION
Check continuity between back door cinching latch unit connector
D502 terminal 8 and ground.
s the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
BACK DOOR HALF SWITCH SIGNAL INSPECTION
Terminals
Back door position
Voltage (V)
(Approx.)
(+)
(-)
7
Ground
Half-latch
0
Open/close
Battery voltage
ALKIA1222ZZ
7 - 6
: Continuity should exist.
7 - Ground
: Continuity should not exist.
ALKIA1225ZZ
8 - Ground
: Continuity should exist.
ALKIA1226ZZ
DLK-248
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR HALF SWITCH
Check continuity between back door cinching latch unit terminals 6
and 8.
s the inspection result normal?
YES
>> Replace back door control unit.
NO
>> Replace back door cinching latch unit.
Terminals
Back door position
Continuity
6
8
Half-latch
Yes
Open/close
No
ALKIA1228ZZ
BACK DOOR CLOSE SWITCH SYSTEM
DLK-249
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR CLOSE SWITCH SYSTEM
Diagnosis Procedure
INFOID:0000000001728550
1.
BACK DOOR CLOSE SWITCH SIGNAL INSPECTION
1.
Turn ignition switch OFF.
2.
While opening and closing the back door, check voltage
between back door control unit connector D509 terminal 8 and
ground.
s the inspection result normal?
YES
>> Switch is OK.
NO
>> GO TO 2.
2.
BACK DOOR CLOSE SWITCH CIRCUIT INSPECTION
1.
Disconnect back door control unit and back door cinching latch unit connectors.
2.
Check continuity between back door control unit connector (A)
D509 terminal 8 and back door cinching latch unit connector (B)
D502 terminal 5.
3.
Check continuity between back door control unit connector (A)
D509 terminal 8 and ground.
s the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
BACK DOOR CLOSE SWITCH GROUND INSPECTION
Check continuity between back door cinching latch unit connector
D502 terminal 8 and ground.
s the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
BACK DOOR CLOSE SWITCH SIGNAL INSPECTION
Terminals
Back door position
Voltage (V)
(Approx.)
(+)
(-)
8
Ground
Open/half-latch
Battery voltage
Closed
0
ALKIA1232ZZ
8 - 5
: Continuity should exist.
8 - Ground
: Continuity should not exist.
ALKIA1233ZZ
8 - Ground
: Continuity should exist.
ALKIA1226ZZ
DLK-250
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR CLOSE SWITCH SYSTEM
Check continuity between back door cinching latch unit terminals 5
and 8.
s the inspection result normal?
YES
>> Replace back door control unit.
NO
>> Replace back door cinching latch unit.
Terminals
Back door position
Continuity
5
8
Half-latch/open
No
Closed
Yes
ALKIA1234ZZ
BACK DOOR NEUTRAL SWITCH
DLK-251
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR NEUTRAL SWITCH
Diagnosis Procedure
INFOID:0000000001728551
1.
BACK DOOR NEUTRAL SWITCH SIGNAL INSPECTION
1.
Turn ignition switch OFF.
2.
While opening and closing the back door, check voltage
between back door control unit connector D509 terminal 9 and
ground.
s the inspection result normal?
YES
>> Switch is OK.
NO
>> GO TO 2.
2.
BACK DOOR NEUTRAL SWITCH CIRCUIT INSPECTION
1.
Disconnect back door control unit and back door cinching latch unit connectors.
2.
Check continuity between back door control unit connector (A)
D509 terminal 9 and back door cinching latch unit connector (B)
D502 terminal 4.
3.
Check continuity between back door control unit connector (A)
D509 terminal 9 and ground.
s the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
BACK DOOR NEUTRAL SWITCH GROUND INSPECTION
Check continuity between back door cinching latch unit connector
D502 terminal 8 and ground.
s the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
BACK DOOR NEUTRAL SWITCH SIGNAL INSPECTION
Terminals
Back door position
Voltage (V)
(Approx.)
(+)
(-)
9
Ground
Half-latch/closed
Battery voltage
Open
0
ALKIA1235ZZ
9 - 4
: Continuity should exist.
9 - Ground
: Continuity should not exist.
ALKIA1236ZZ
8 - Ground
: Continuity should exist.
ALKIA1226ZZ
DLK-252
< COMPONENT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR NEUTRAL SWITCH
Check continuity between back door cinching latch unit terminals 4
and 8.
s the inspection result normal?
YES
>> Replace back door control unit.
NO
>> Replace back door cinching latch unit.
Terminals
Back door position
Continuity
4
8
Half-latch/closed
No
Open
Yes
ALKIA1237ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст