Nissan Pathfinder (2008 year). Manual — part 262
P0335 CKP SENSOR (POS)
EC-213
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
5.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F32, E2
• Harness for open or short between crankshaft position sensor (POS) and ground
>> Repair open circuit or short to power in harness or connectors.
6.
CHECK CKP SENSOR (POS) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 13 and CKP sensor (POS) terminal 2.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK CRANKSHAFT POSITION SENSOR (POS)
EC-213, "Component Inspection"
OK or NG
OK
>> GO TO 8.
NG
>> Replace crankshaft position sensor (POS).
8.
CHECK GEAR TOOTH
Visually check for chipping signal plate gear tooth.
OK or NG
OK
>> GO TO 9.
NG
>> Replace the signal plate.
9.
CHECK INTERMITTENT INCIDENT
.
>> INSPECTION END
Component Inspection
INFOID:0000000001376005
CRANKSHAFT POSITION SENSOR (POS)
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect crankshaft position sensor (POS) harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
Continuity should exist.
PBIB0563E
EC-214
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0335 CKP SENSOR (POS)
5.
Check resistance as shown in the figure.
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
1 (+) - 3 (-)
2 (+) - 3 (-)
PBIB0564E
P0340, P0345 CMP SENSOR (PHASE)
EC-215
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0340, P0345 CMP SENSOR (PHASE)
Component Description
INFOID:0000000001376006
The camshaft position sensor (PHASE) senses the retraction of
intake valve camshaft to identify a particular cylinder. The camshaft
position sensor (PHASE) senses the piston position.
When the crankshaft position sensor (POS) system becomes inoper-
ative, the camshaft position sensor (PHASE) provides various con-
trols of engine parts instead, utilizing timing of cylinder identification
signals.
The sensor consists of a permanent magnet and Hall IC.
When engine is running, the high and low parts of the teeth cause
the gap with the sensor to change.
The changing gap causes the magnetic field near the sensor to
change.
Due to the changing magnetic field, the voltage from the sensor changes.
ECM receives the signals as shown in the figure.
On Board Diagnosis Logic
INFOID:0000000001376008
DTC Confirmation Procedure
INFOID:0000000001376009
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5V with igni-
tion switch ON.
1.
Crank engine for at least 2 seconds and run it for at least 5 seconds at idle speed.
2.
Check 1st trip DTC.
3.
If 1st trip DTC is detected, go to
If 1st trip DTC is not detected, go to next step.
4.
Maintaining engine speed at more than 800 rpm for at least 5 seconds.
5.
Check 1st trip DTC.
6.
If 1st trip DTC is detected, go to
PBIB0562E
PBIB2744E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0340
0340
(Bank 1)
Camshaft position sen-
sor (PHASE) circuit
• The cylinder No. signal is not sent to ECM for
the first few seconds during engine cranking.
• The cylinder No. signal is not sent to ECM
during engine running.
• The cylinder No. signal is not in the normal
pattern during engine running.
• Harness or connectors
(The sensor circuit is open or shorted)
• Camshaft position sensor (PHASE)
• Camshaft (Intake)
• Starter motor
• Starting system circuit
• Dead (Weak) battery
P0345
0345
(Bank 2)
EC-216
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0340, P0345 CMP SENSOR (PHASE)
Diagnosis Procedure
INFOID:0000000001376011
1.
CHECK STARTING SYSTEM
Turn ignition switch to START position.
Yes or No
Yes
>> GO TO 2.
No
>> Check starting system. (Refer to
2.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace ground connections.
3.
CHECK CAMSHAFT POSITION (CMP) SENSOR (PHASE) POWER SUPPLY CIRCUIT
1.
Disconnect camshaft position (CMP) sensor (PHASE) harness
connector.
2.
Turn ignition switch ON.
3.
Check voltage between CMP sensor (PHASE) terminal 3 and
ground with CONSULT-III or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E2, F32
• Harness for open or short between camshaft position sensor (PHASE) and ECM
Does the engine turn over?
Does the starter motor operate?
BBIA0539E
BBIA0549E
Voltage: Battery voltage
SEF481Y
P0340, P0345 CMP SENSOR (PHASE)
EC-217
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• Harness for open or short between camshaft position sensor (PHASE) and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK CMP SENSOR (PHASE) GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check harness continuity between CMP sensor (PHASE) terminal 1 and ground.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors F32, E2
• Harness for open or short between CMP sensor (PHASE) and ground
>> Repair open circuit or short to power in harness or connectors.
7.
CHECK CMP SENSOR (PHASE) INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Disconnect ECM harness connector.
2.
Check harness continuity between ECM terminal 33 (bank 1) or 14 (bank 2) and CMP sensor (PHASE)
terminal 2.
Refer to Wiring Diagram.
3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 8.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK CAMSHAFT POSITION SENSOR (PHASE)
EC-218, "Component Inspection"
OK or NG
OK
>> GO TO 9.
NG
>> Replace malfunctioning camshaft position sensor (PHASE).
9.
CHECK CAMSHAFT (INTAKE)
Check the following.
• Accumulation of debris to the signal plate of camshaft rear end
• Chipping signal plate of camshaft rear end
OK or NG
OK
>> GO TO 10.
NG
>> Remove debris and clean the signal plate of camshaft
rear end or replace camshaft.
10.
CHECK INTERMITTENT INCIDENT
.
Continuity should exist.
Continuity should exist.
SEC905C
EC-218
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0340, P0345 CMP SENSOR (PHASE)
>> INSPECTION END
Component Inspection
INFOID:0000000001376012
CAMSHAFT POSITION SENSOR (PHASE)
1.
Loosen the fixing bolt of the sensor.
2.
Disconnect camshaft position sensor (PHASE) harness connector.
3.
Remove the sensor.
4.
Visually check the sensor for chipping.
5.
Check resistance as shown in the figure.
PBIB0563E
Terminal No. (Polarity)
Resistance
Ω
[at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
1 (+) - 3 (-)
2 (+) - 3 (-)
PBIB0564E
P0420, P0430 THREE WAY CATALYST FUNCTION
EC-219
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0420, P0430 THREE WAY CATALYST FUNCTION
On Board Diagnosis Logic
INFOID:0000000001376191
The ECM monitors the switching frequency ratio of air fuel ratio (A/F)
sensor 1 and heated oxygen sensor 2.
A three way catalyst (manifold) with high oxygen storage capacity
will indicate a low switching frequency of heated oxygen sensor 2.
As oxygen storage capacity decreases, the heated oxygen sensor 2
switching frequency will increase.
When the frequency ratio of air fuel ratio (A/F) sensor 1 and heated
oxygen sensor 2 approaches a specified limit value, the three way
catalyst (manifold) malfunction is diagnosed.
DTC Confirmation Procedure
INFOID:0000000001376192
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
WITH CONSULT-III
TESTING CONDITION:
Do not hold engine speed for more than the specified minutes below.
1.
Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.
2.
Start engine and warm it up to the normal operating temperature.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Turn ignition switch ON.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
7.
Let engine idle for 1 minute.
8.
Make sure that “COOLAN TEMP/S” indicates more than 70
°
C (158
°
F).
If not, warm up engine and go to next step when “COOLAN TEMP/S” indication reaches to 70
°
C (158
°
F).
9.
Open engine hood.
10. Select “DTC & SRT CONFIRMATION” then “SRT WORK SUPPORT” mode with CONSULT-III.
11. Rev engine up to 2,000 to 3,000 rpm and hold it for 3 consecutive minutes then release the accelerator
pedal completely.
If “INCMP” of “CATALYST” changed to “CMPLT”, go to step 12.
12. Wait 5 seconds at idle.
13. Rev engine up to 2,000 to 3,000 rpm and maintain it until “INCMP” of “CATALYST” changes to “CMPLT” (It
will take approximately 5 minutes).
If not “CMPLT”, stop engine and cool it down to less than 70
°
C (158
°
F) and then retest from step 1.
14. Select “SELF-DIAG RESULTS” mode with CONSULT-III.
PBIB2377E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0420
0420
(Bank 1)
Catalyst system efficien-
cy below threshold
• Three way catalyst (manifold) does not oper-
ate properly.
• Three way catalyst (manifold) does not have
enough oxygen storage capacity.
• Three way catalyst (manifold)
• Exhaust tube
• Intake air leaks
• Fuel injector
• Fuel injector leaks
• Spark plug
• Improper ignition timing
P0430
0430
(Bank 2)
EC-220
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0420, P0430 THREE WAY CATALYST FUNCTION
15. Confirm that the 1st trip DTC is not detected.
If the 1st trip DTC is detected, go to
.
Overall Function Check
INFOID:0000000001376193
Use this procedure to check the overall function of the three way catalyst (manifold). During this check, a 1st
trip DTC might not be confirmed.
WITH GST
1.
Start engine and warm it up to the normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
6.
Let engine idle for 1 minute.
7.
Open engine hood.
8.
Set voltmeter probe between ECM terminals 74 [HO2S2 (bank
1) signal], 55 [HO2S2 (bank 2) signal] and ground.
9.
Keep engine speed at 2,500 rpm constant under no load.
10. Make sure that the voltage does not vary for more than 5 sec-
onds.
If the voltage fluctuation cycle takes less than 5 seconds, go to
• 1 cycle: 0.6 - 1.0
→
0 - 0.3
→
0.6 - 1.0
Diagnosis Procedure
INFOID:0000000001376194
1.
CHECK EXHAUST SYSTEM
Visually check exhaust tubes and muffler for dent.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace.
2.
CHECK EXHAUST GAS LEAK
1.
Start engine and run it at idle.
2.
Listen for an exhaust gas leak before the three way catalyst (manifold).
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace.
3.
CHECK INTAKE AIR LEAK
Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK
>> GO TO 4.
PBIB1108E
PBIB1216E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст