Nissan Pathfinder (2008 year). Manual — part 194
DLN-136
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
FRONT OIL SEAL
FRONT OIL SEAL
Removal and Installation
INFOID:0000000001282261
REMOVAL
1.
Partially drain the transfer fluid. Refer to
2.
Remove the front propeller shaft. Refer to
DLN-308, "Removal and Installation"
.
3.
Remove the companion flange self-lock nut using Tool.
4.
Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
5.
Remove the companion flange using suitable tool.
6.
Remove the front oil seal from the front case using Tool.
CAUTION:
Do not damage front case.
INSTALLATION
Tool number
: KV40104000 (
—
)
SDIA2657E
SDIA2658E
WDIA0193E
Tool number
: ST33290001 (J-34286)
LDIA0144E
FRONT OIL SEAL
DLN-137
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1.
Install the new front oil seal until it is flush with the end face of
the front case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2.
Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3.
Install the new self-lock nut. Tighten to the specified torque
using Tool. Refer to
DLN-149, "Disassembly and Assembly"
.
CAUTION:
Do not reuse self-lock nut.
4.
Install the front propeller shaft. Refer to
.
5.
Refill the transfer with fluid and check for fluid leakage and fluid
level. Refer to
Tool number
: KV38100500 (
—
)
SDIA2662E
SDIA2658E
Tool number
: KV40104000 (
—
)
LDIA0147E
DLN-138
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
REAR OIL SEAL
REAR OIL SEAL
Removal and Installation
INFOID:0000000001282262
REMOVAL
1.
Partially drain the transfer fluid. Refer to
2.
Remove the rear propeller shaft. Refer to
DLN-316, "Removal and Installation"
3.
Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
4.
Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1.
Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2.
Apply petroleum jelly to the circumference of the new dust cover.
Position the new dust cover using the identification mark as
shown.
CAUTION:
• Do not reuse dust cover.
• Position the identification mark at the position shown.
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: ST30720000 (J-25405)
LDIA0140E
SDIA3436E
REAR OIL SEAL
DLN-139
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3.
Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
4.
Install the rear propeller shaft. Refer to
.
5.
Refill the transfer with fluid and check for fluid leakage and fluid
level. Refer to
Tool number
: KV40105310 (
—
)
PDIA0116E
DLN-140
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
SIDE OIL SEAL
SIDE OIL SEAL
Removal and Installation
INFOID:0000000001282263
REMOVAL
1.
Remove the front propeller shaft. Refer to
DLN-308, "Removal and Installation"
.
2.
Remove the companion flange. Refer to
DLN-288, "Disassembly and Assembly"
.
3.
Remove the transfer control device from the transfer assembly. Refer to
DLN-275, "Removal and Installa-
4.
Remove the side oil seal using suitable tool.
CAUTION:
Do not damage shift cross.
INSTALLATION
1.
Install the new side oil seal until it is flush with the end face of
case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2.
Install the transfer control device to the transfer assembly. Refer
to
DLN-275, "Removal and Installation"
3.
Install the companion flange. Refer to
.
4.
Install the front propeller shaft. Refer to
DLN-308, "Removal and Installation"
SDIA2666E
Tool number
: ST22360002 (J-25679-01)
SDIA2665E
TRANSFER CONTROL DEVICE
DLN-141
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000001282264
CAUTION:
• Change vehicle state to 2WD, and then remove and install transfer control device.
• Check 4WD shift indicator after installation. Refer to
DLN-125, "Precaution for Transfer Assembly
and Transfer Control Unit Replacement"
1.
Shift lever
2.
Actuator
SDIA2654E
DLN-142
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000001282265
VQ40DE
CAUTION:
• Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
• Install each air breather hose into the breather tube (metal
connector) until the hose end reaches the end of the curve
section. Set each air breather hose with paint mark facing
upward.
• Install actuator/transfer motor air breather hose and transfer
air breather hose on clip A with the paint mark facing upward.
SDIA3339E
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Clip E
7.
Actuator
8.
Air breather hose clamp
9.
Clip F
10. Transfer motor
11.
Breather tube (transfer)
SDIA3340E
SDIA3342E
AIR BREATHER HOSE
DLN-143
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install clip C on actuator/transfer motor air breather hose and
transfer air breather hose with the paint mark matched.
• Install actuator/transfer motor air breather hose and transfer
air breather hose on clip D and clip E with the paint mark fac-
ing upward.
• Install the actuator air breather hose into the actuator (case
connector) until the hose end reaches the base of the tube.
Set actuator air breather hose with paint mark facing leftward.
• Install clip F on transfer motor air (control device) breather
hose and transfer air breather hose with the paint mark
matched.
SDIA3343E
SDIA3344E
SDIA3226E
SDIA3345E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст