Nissan Pathfinder (2008 year). Manual — part 569
SRC-34
< COMPONENT DIAGNOSIS >
B1193 – B1196 SIDE CURTAIN AIR BAG MODULE RH (FRONT)
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 5
5.
RELATED HARNESS
Replace the related harness.
>> END
B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
SRC-35
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
Description
INFOID:0000000001277739
DTC B1150 – B1153 LH SIDE CURTAIN AIR BAG MODULE (REAR)
The LH side curtain air bag module (rear) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the LH side curtain air bag module (rear).
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000001277740
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.
DTC
If DTC is detected. Refer to
SRC-36, "Diagnosis Procedure (Component diagnosis)"
.
>> END
CONSULT-III name
DTC
DTC detecting condition
Repair order
CURTAIN MODULE LH
[OPEN]
B1150
LH side curtain air bag module (rear) circuit
is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the LH side curtain air bag module.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
CURTAIN MODULE LH
[VB-SHORT]
B1151
LH side curtain air bag module (rear) circuit
is shorted to a power supply circuit.
CURTAIN MODULE LH
[GND-SHORT]
B1152
LH side curtain air bag module (rear) circuit
is shorted to ground.
CURTAIN MODULE LH
[SHORT]
B1153
LH side curtain air bag module (rear) cir-
cuits are shorted to each other.
WHIA0254E
SRC-36
< COMPONENT DIAGNOSIS >
B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000001277741
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
LH SIDE CURTAIN AIR BAG MODULE
Replace the LH side curtain air bag module. Refer to
SR-11, "Removal and Installation"
.
>> GO TO 4
4.
AIR BAG DIAGNOSIS SENSOR UNIT
B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
SRC-37
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Replace the air bag diagnosis sensor unit.
SR-15, "Removal and Installation"
.
>> GO TO 5
5.
RELATED HARNESS
Replace the related harness.
>> END
SRC-38
< COMPONENT DIAGNOSIS >
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
Description
INFOID:0000000001277742
DTC B1145 – B1148 RH SIDE CURTAIN AIR BAG MODULE (REAR)
The RH side curtain air bag module (rear) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module (rear).
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000001277743
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.
DTC
If DTC is detected. Refer to
SRC-39, "Diagnosis Procedure (Component diagnosis)"
.
>> END
CONSULT-III name
DTC
DTC detecting condition
Repair order
CURTAIN MODULE RH
[OPEN]
B1145
RH side curtain air bag module (rear) cir-
cuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the RH side curtain air bag module.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
CURTAIN MODULE RH
[VB-SHORT]
B1146
RH side curtain air bag module (rear) cir-
cuit is shorted to a power supply circuit.
CURTAIN MODULE RH
[GND-SHORT]
B1147
RH side curtain air bag module (rear) cir-
cuit is shorted to ground.
CURTAIN MODULE RH
[SHORT]
B1148
RH side curtain air bag module (rear) cir-
cuits are shorted to each other.
WHIA0252E
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
SRC-39
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.
WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.
REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.
DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to
.
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000001277744
Recheck SRS after each replacement.
1.
HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 2
2.
WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
YES
>> Replace the harness.
NO
>> GO TO 3
3.
RH SIDE CURTAIN AIR BAG MODULE
Replace the RH side curtain air bag module. Refer to
SR-11, "Removal and Installation"
>> GO TO 4
4.
AIR BAG DIAGNOSIS SENSOR UNIT
SRC-40
< COMPONENT DIAGNOSIS >
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
Replace the air bag diagnosis sensor unit. Refer to
SR-15, "Removal and Installation"
>> GO TO 5
5.
RELATED HARNESS
Replace the related harness.
>> END
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
SRC-41
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
Description
INFOID:0000000001277745
DTC B1086 – B1089 SEAT BELT PRE-TENSIONER LH
The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner LH.
PART LOCATION
SRC-7, "SRS Component Parts Location"
DTC Logic
INFOID:0000000001277746
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.
CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.
DTC
If DTC is detected. Refer to
SRC-42, "Diagnosis Procedure (Component diagnosis)"
.
>> END
CONSULT-III name
DTC
DTC detecting condition
Repair order
PRE-TEN FRONT LH
[OPEN]
B1086
LH seat belt pre-tensioner circuit is open.
1.
Visually check the wiring harness connection.
2.
Replace the harness if it has visible damage.
3.
Replace the front LH seat belt pre-tensioner.
4.
Replace the air bag diagnosis sensor unit.
5.
Replace the related harness.
PRE-TEN FRONT LH
[VB-SHORT]
B1087
LH seat belt pre-tensioner circuit is shorted
to a power supply circuit.
PRE-TEN FRONT LH
[GND-SHORT]
B1088
LH seat belt pre-tensioner circuit is shorted
to ground.
PRE-TEN FRONT LH
[SHORT]
B1089
LH seat belt pre-tensioner circuits are
shorted to each other.
WHIA0263E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст