Nissan Pathfinder (2008 year). Manual — part 619
TM-294
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
15. Install seal rings to drum support.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Install snap ring in transmission case while compressing return
spring using Tool.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
18. Install reverse brake drive plates driven plates and dish plates in
transmission case.
CAUTION:
Take care with order of plates.
• VQ40DE models
- Snap ring (1)
- Retaining plate (2)
- Drive plate (3)
- Driven plate (4)
- Dish plate (5)
- Driveplate/Driven plate:6/6
SCIA3333E
SCIA2324E
Tool number
: KV31102400 (J-34285 and J-34285-87)
SCIA5877E
SCIA6949E
ASSEMBLY
TM-295
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CAUTION:
Take care with order of plates.
• VK56DE models
- Snap ring (1)
- Retaining plate (2)
- Drive plate (3)
- Driven plate (4)
- Dish plate (5)
- Driveplate/Driven plate: 7/7
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
WCIA0625E
SCIA5249E
SCIA2439E
TM-296
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
22. Measure clearance (A) between retaining plate and snap ring. If
not within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-248, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
24. Install revolution sensor to transmission case and tighten bolt to
specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
25. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
Clearance “A”
: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate
: Refer to
SCIA3129E
SCIA5031E
Revolution sensor bolt
: 5.8 N·m (0.59 kg-m, 51 in-lb)
SCIA2320E
Tool number
: ST33400001 (J-26082)
WCIA0475E
ASSEMBLY
TM-297
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
SCIA6180J
SCIA3424E
SCIA3423E
SCIA6179J
SCIA5209E
TM-298
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION:
Do not mistake front of shaft for rear because both sides
look similar (thinner end is front side).
33. Install bearing race to output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (4WD models) according to the
following procedures.
a.
2WD models
i.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-26, "Recommended Chemical Prod-
.) to rear extension assembly as shown.
CAUTION:
Completely remove all moisture, oil, old sealant and any
foreign material from the transmission case and rear exten-
sion assembly mating surfaces.
SCIA5247E
SCIA5030E
SCIA5245E
SCIA5212E
ASSEMBLY
TM-299
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ii.
Install rear extension assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
iii.
Install brackets (VK56DE models only)
iv.
Tighten rear extension assembly bolts to specified torque.
• 1: Self sealing bolts
• 2: Rear extension assembly bolts
CAUTION:
Do not reuse self-sealing bolt.
b.
4WD models
i.
Install gasket onto transmission case.
CAUTION:
• Completely remove all moisture, oil, old gasket and any
foreign material from the transmission case and adapter
case assembly mating surfaces.
• Do not reuse gasket.
ii.
Install adapter case assembly to transmission case.
CAUTION:
Insert the tip of parking rod between the parking pawl and
the parking actuator support when assembling the rear
extension assembly.
SCIA5029E
Rear extension
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m, 45 ft-lb)
WCIA0562E
SCIA5231E
SCIA5186E
TM-300
< DISASSEMBLY AND ASSEMBLY >
ASSEMBLY
iii.
Install brackets (VK56DE models only)
• 1: Brackets
• 2: Self-sealing bolts
iv.
Tighten adapter case assembly to specified torque.
• 1:
• 2: Brackets
• 3: Self-sealing bolts
CAUTION:
Do not reuse self-sealing bolt (2).
35. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
WCIA0563E
Adapter case
assembly bolt
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA7220E
SCIA5019E
ASSEMBLY
TM-301
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
36. Install needle bearing in drum support.
CAUTION:
Apply petroleum jelly to needle bearing.
37. Install high and low reverse clutch assembly in direct clutch.
38. Align the drive plate using suitable tool.
39. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
CAUTION:
SCIA5198E
SCIA2306E
SCIA3169E
SCIA5018E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст