Nissan Pathfinder (2008 year). Manual — part 218
DLN-328
< DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1350]
PROPELLER SHAFT
Journal
1.
Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2.
Select new snap rings that will provide the specified play in an
axial direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3.
Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4.
Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
WPD019
APD012
SPD732
LDIA0119E
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-329
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 2S1350]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000001315156
2WD models
Unit: mm (in)
Propeller Shaft Runout
Unit: mm (in)
Propeller Shaft Joint Flex Effort
Unit: N·m (kg-m, lb)
Journal Axial Play
Unit: mm (in)
4WD models
Propeller Shaft Runout
Propeller Shaft Joint Flex Effort
Applied model
2WD
VK56DE
A/T
Propeller shaft model
2S1350 (aluminum tube)
Number of joints
2
Coupling method with rear final drive
Flange type
Coupling method with transmission
Sleeve type
Shaft length (Spider to spider)
1360 mm (53.54 in)
Shaft outer diameter
127.6 mm (5.02 in)
Item
Limit
Propeller shaft runout
1.02 mm (0.0402 in) or less
Item
Limit
Propeller shaft joint flex effort
2.26 N·m (0.23 kg-m, 20 in-lb) or less
Item
Limit
Journal axial play
0.02 mm (0.0008 in) or less
Applied model
4WD
VK56DE
A/T
Propeller shaft model
2S1350 (aluminum tube)
Number of joints
2
Coupling method with rear final drive
Flange type
Coupling method with transfer
Sleeve type
Shaft length (Spider to spider)
1167.2 mm (45.95 in)
Shaft outer diameter
102.5 mm (4.04 in)
Item
Limit
Propeller shaft runout
0.6 mm (0.024 in) or less
Item
Limit
Propeller shaft joint flex effort
2.26 N·m (0.23 kg-m, 20 in-lb) or less
DLN-330
< SERVICE DATA AND SPECIFICATIONS (SDS)
[PROPELLER SHAFT: 2S1350]
SERVICE DATA AND SPECIFICATIONS (SDS)
Journal Axial Play
Snap Ring
INFOID:0000000001315157
Model 2F1310 and 2S1330 (4WD)
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Model 2S1330 (2WD)
Unit: mm (in)
*Always check with the Parts Department for the latest parts information.
Item
Limit
Journal axial play
0.02 mm (0.0008 in) or less
Thickness
Color
Part Number*
1.99 (0.0783)
White
37146-C9400
2.02 (0.0795)
Yellow
37147-C9400
2.05 (0.0807)
Red
37148-C9400
2.08 (0.0819)
Green
37149-C9400
2.11 (0.0831)
Blue
37150-C9400
2.14 (0.0843)
Light brown
37151-C9400
2.17 (0.0854)
Black
37152-C9400
2.20 (0.0866)
No paint
37153-C9400
Thickness
Color
Part Number*
1.600 - 1.638 (0.0630 - 0.0645)
Black
37146-EA500
1.549 - 1.588 (0.0610 - 0.0625)
Black
37147-EA500
1.524 - 1.562 (0.0600 - 0.0615)
Black
37148-EA500
1.499 - 1.537 (0.0590 - 0.0605)
Black
37149-EA500
PRECAUTIONS
DLN-331
< PRECAUTION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Servicing Front Final Drive
INFOID:0000000001297270
• Before starting diagnosis of the vehicle, understand the symptoms well. Perform correct and systematic
operations.
• Check for the correct installation status prior to removal or disassembly. When matching marks are required,
be certain they do not interfere with the function of the parts they are applied to.
• Overhaul should be done in a clean work area, a dust proof area is recommended.
• Before disassembly, completely remove sand and mud from the exterior of the unit, preventing them from
entering into the unit during disassembly or assembly.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or a shop cloth to prevent the entering of lint.
• Check appearance of the disassembled parts for damage, deformation, and abnormal wear. Replace them
with new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time the unit is disassembled.
• Clean and flush the parts sufficiently and blow them dry.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mating surface; then remove any moisture, oil, and
foreign materials from the application and mating surfaces.
• In principle, tighten nuts or bolts gradually in several steps working diagonally from inside to outside. If a
tightening sequence is specified, observe it.
• During assembly, observe the specified tightening torque.
• Add new differential gear oil, petroleum jelly, or multi-purpose grease, as specified.
DLN-332
< PREPARATION >
[FRONT FINAL DRIVE: R180A]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000001297271
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV38108300
(J-44195)
Flange wrench
Removing and installing drive pinion lock nut
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
• Installing front oil seal
• Installing side oil seal
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
ST27863000
(
—
)
Drift
• Installing front oil seal
• Installing side oil seal
a: 74.5 mm (2.933 in) dia.
b: 62.5 mm (2.461 in) dia.
ST3127S000
(J-25765-A)
Preload gauge
1: GG91030000
(J-25765)
Torque wrench
2: HT62940000
(
—
)
Socket adapter (1/2
″
)
3: HT62900000
(
—
)
Socket adapter (3/8
″
)
Measuring drive pinion bearing preload torque
and total preload torque
NT771
ZZA0601D
ZZA0811D
ZZA1003D
NT124
PREPARATION
DLN-333
< PREPARATION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ST3306S001
(
—
)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
Removing and installing side bearing inner
race
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
ST30031000
(J-22912-01)
Replacer
Removing drive pinion rear bearing inner race
KV38100600
(J-25267)
Drift
Installing side bearing adjusting washer
ST30613000
(J-25742-3)
Drift
Installing drive pinion rear bearing outer race
a: 72 mm (2.83 in) dia.
b: 48 mm (1.89 in) dia.
ST30611000
(J-25742-1)
Drift bar
Installing drive pinion rear bearing outer race
(Use with ST30613000)
KV38100200
(J-26233)
Drift
Installing drive pinion front bearing outer race
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
Tool number
(Kent-Moore No.)
Tool name
Description
S-NT046
NT072
ZZA0700D
SDIA0429J
ZZA1000D
S-NT090
ZZA1143D
DLN-334
< PREPARATION >
[FRONT FINAL DRIVE: R180A]
PREPARATION
Commercial Service Tool
INFOID:0000000001297272
ST30901000
(J-26010-01)
Drift
Installing drive pinion rear bearing inner race
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.
ST33200000
(J-26082)
Drift
Installing drive pinion front bearing inner race
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.
ST33230000
(J-35867)
Drift
Installing side bearing inner race
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28 mm (1.10 in) dia.
(
—
)
(J-34309)
Differential shim selector tool
Adjusting bearing preload and drive pinion
height
(
—
)
(J-25269-18)
Side bearing disc (2 Req'd)
Selecting drive pinion height adjusting washer
KV10112100
(BT-8653-A)
Angle wrench
Tightening bolts for drive gear
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA0978D
ZZA1002D
ZZA1046D
NT134
NT135
NT014
PREPARATION
DLN-335
< PREPARATION >
[FRONT FINAL DRIVE: R180A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Tool name
Description
Power tool
Loosening nuts and bolts
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст