Nissan Versa Note. Manual — part 530
HEADLINING
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000008969714
REMOVAL
1. Remove front pillar finishers (LH/RH). Refer to
INT-21, "FRONT PILLAR FINISHER : Removal and Instal-
.
2. Remove sun visor screws and sun visorS (LH/RH).
3. Remove map lamp (if equipped). Refer to
INL-51, "Removal and Installation"
4. Remove interior room lamp. Refer to
INL-53, "Removal and Installation"
5. Remove microphone (if equipped). Refer to
AV-59, "Removal and Installation"
6. Remove center pillar upper finishers (LH/RH). Refer to
INT-25, "CENTER PILLAR UPPER FINISHER :
.
7. Remove luggage side upper finishers (LH/RH). Refer to
INT-35, "LUGGAGE SIDE UPPER FINISHER :
.
8. Insert a suitable tool (A) at approximately a 30 degree angle into
the sun visor holder notch on the front of the sun visor holder (1)
and press in the locking tab (B) to release it. While holding in
lock tab (B), rotate the sun visor holder (1) 90 degrees to release
it from the headlining.
: Front
CAUTION:
Do not force the sun visor holder when removing as the
locking tab may be damaged if the suitable tool is not posi-
tioned correctly.
NOTE:
If the sun visor holder (1) does not fully rotate, make sure that
the suitable tool (A) is pressing in on the locking tab (B) and is
not positioned under locking tab (B). Reinsert the suitable tool
(A) as necessary to release the locking tab (B).
9. Release assist grip pawls and remove bolt (A) using a suitable
tool and remove all assist grips.
:Pawl
10. Remove headlining clips.
11. Remove headlining through the back door.
CAUTION:
• Do not reuse headlining.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Remove all remaining adhesive from roof panel.
• Do not reuse headlining. Replace with new part after removal.
ALJIA0537ZZ
AWJIA1126ZZ
INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
• Apply adhesive as shown before installing headlining.
• Do not bend headlining when installing.
• When installing headlining, start by installing both sun visor holders and headlining clips to hold
headlining in position.
• Be careful that the surface is not wrinkled when installing.
1. Headlining
A. Adhesive application location
B. Adhesive
C. 8 mm
D. 5 mm
AWJIA1102ZZ
LUGGAGE TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE TRIM
Exploded View
INFOID:0000000008969715
LUGGAGE REAR PLATE
1.
Parcel shelf finisher (if equipped)
2.
Luggage floor board (if equipped)
3.
Luggage side upper finisher (LH)
4.
Luggage side front reinforcement (LH) 5.
Luggage side rear reinforcement (LH) 6.
Luggage side lower finisher (LH)
7.
Luggage rear plate
8.
Luggage side lower finisher (RH)
9.
Luggage side rear reinforcement (RH)
10. Luggage side front reinforcement
(RH)
11. Luggage side upper finisher (RH)
12. Luggage side front cover (RH)
13. Luggage side clip
14. Luggage side rear cover (RH)
15. Luggage floor box
16. Luggage side rear cover (LH)
17. Luggage side front cover (LH)
18. Luggage floor trim
Pawl
Metal clip
Clip
Front
AWJIA1129ZZ
I N
T
- 3
4
< REMOVAL AND INSTALLATION >
LUGGAGE TRIM
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000008969716
REMOVAL
1. Remove luggage floor board (if equipped).
2. Remove luggage floor trim.
3. Remove luggage rear plate clips (A).
4. Release luggage rear plate clips using a suitable tool (A) and
remove luggage rear plate as shown.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation.
• When installing luggage rear plate, check that clips are securely placed into body holes.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000008969717
REMOVAL
1. Partially remove rear body side welt. Refer to
INT-24, "BODY SIDE WELT : Removal and Installation"
2. Remove luggage floor board (if equipped).
3. Remove luggage floor trim.
4. Remove seat back hinge. Refer to
SE-31, "SEATBACK HINGE : Removal and Installation"
5. Release rear parcel shelf finisher clips using a suitable tool and remove rear parcel shelf finisher (if
equipped).
6. Remove luggage side lower finisher pawls using a suitable tool.
AWJIA1127ZZ
AWJIA1128ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст