Nissan Versa Note. Manual — part 529
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000009446822
Removal and Installation
INFOID:0000000008969712
WARNING:
• Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait at
least three minutes.
• Do not drop the seat belt retractor. Always handle it with care.
• Always point pretensioner cylinder away from body when handling.
REMOVAL
1. Remove front seats. Refer to
SE-20, "DRIVER SIDE : Removal and Installation"
(Driver side) and
"PASSENGER SIDE : Removal and Installation"
(Passenger side).
2. Remove rear seatback hinge. Refer to
SE-31, "SEATBACK HINGE : Removal and Installation"
3. Remove center console lower. Refer to
IP-20, "Removal and Installation"
4. Remove dash side finishers (LH/RH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installa-
5. Remove center pillar lower finishers (LH/RH). Refer to
INT-25, "CENTER PILLAR LOWER FINISHER :
.
1.
Harness clip A
2.
Harness clip B
3.
Floor trim
4.
Carpet hook
5.
Front floor spacer (RH)
6.
Front floor spacer (LH)
7.
Rear floor spacer (LH)
8.
Rear floor spacer (RH)
Front
Clip
AWJIA1142ZZ
INT-28
< REMOVAL AND INSTALLATION >
FLOOR TRIM
6. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
"Removal and Installation (Battery)"
.
WARNING:
Before servicing the SRS, turn the ignition switch off, disconnect both battery terminals then wait
at least three minutes.
7. Disconnect the harness connector (A) from the seat belt retrac-
tor (1).
WARNING:
• Do not drop the seat belt retractor. Always handle it with
care.
• Always point pretensioner cylinder away from body when
handling.
CAUTION:
• For removing/installing the shoulder belt pre-tensioner
harness connector, insert a thin screwdriver wrapped in
tape into the notch, then lift the lock and remove the har-
ness connector as shown.
• Install the harness connector with the lock raised, and
push the lock into the harness connector as shown.
• After installing the harness connector, check that the lock
is pushed in securely.
8. Remove seat belt lower anchor bolt.
CAUTION:
Before removing the seat belt lower anchor bolt, note the positions of washers and spacers for
correct installation.
9. Remove diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
.
10. Remove shift selector. Refer to (5MT) or
TM-229, "Removal and Installation"
(CVT)
11. Remove A/C unit assembly bolt (C) and bracket (1) from vehicle.
12. Remove instrument panel lower bracket bolt (B) and screw (A)
and reposition bracket as necessary to remove floor trim.
ALHIA0316ZZ
PHIA0953J
ALJIA0712ZZ
FLOOR TRIM
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
13. Release carpet hook clips with a suitable tool (A) and remove.
: Clip
14. Release pawls using a suitable tool (A) and open the harness
clips.
: Pawl
15. Remove floor trim.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Replace harness protector B with a new part after removal. Do not reuse harness protector B.
AWJIA0736ZZ
AWJIA0737ZZ
INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000008969713
1. Headlining
2. Rear assist grip (RH)
3. Front assist grip (RH)
4. Microphone (if equipped)
5. Sun visor holder (RH)
6. Sun visor holder (LH)
7. Map lamp (if equipped)
8. Sun visor (RH)
9. Sun visor (LH)
10. Interior room lamp
11. Rear assist grip (LH)
A. Headlining clip
Pawl
AWJIA1143ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст