Nissan Versa Note. Manual — part 760
STEERING COLUMN
ST-9
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING COLUMN
Exploded View
INFOID:0000000009385534
Removal and Installation
INFOID:0000000009385535
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed; the vehicle keys must be
re-registered in the BCM. Refer to CONSULT operations manual.
• Care must be taken not to rotate the steering gear during the removal or installation of the steering
column.
• Care must be taken not to allow axial impact to the steering column during removal or installation.
REMOVAL
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the lowest position.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
4. Remove spiral cable. Refer to
SR-15, "Removal and Installation"
.
5. Remove combination switch. Refer to
EXL-103, "Removal and Installation"
.
6. Remove the cluster lid A. Refer to
IP-21, "Removal and Installation"
.
7. Disconnect the switch harness connectors.
8. Remove the key cylinder if necessary. Refer to
TM-235, "Removal and Installation"
.
9. Set the steering column tilt to the middle position.
CAUTION:
Do not change the position of the tilt mechanism until the steering column is reinstalled.
10. Loosen the steering shaft lower joint bolt.
11. Remove the steering intermediate shaft upper bolt and separate the steering intermediate shaft from the
steering column. Refer to
ST-12, "Removal and Installation"
.
CAUTION:
• Place a matching mark on both steering intermediate shaft and steering column before removing
the steering intermediate shaft.
• When removing steering intermediate shaft, do not insert any tool into the yoke groove to pull
out the steering intermediate shaft or damage could occur. Replace steering intermediate shaft if
damaged.
1.
Steering column
2.
Clamp
AWGIA0294ZZ
ST-10
< REMOVAL AND INSTALLATION >
STEERING COLUMN
12. Disconnect EPS control unit harness connectors.
13. Remove steering column.
14. Remove EPS control unit from steering column if necessary. Refer to
STC-37, "Removal and Installation"
.
15. Remove clamp from steering column if necessary.
16. Inspect steering column after removal. Refer to
INSTALLATION
CAUTION:
• During installation, finger-tighten all of the bracket and joint retaining bolts, then tighten them to
specification.
• When installing the steering column cover, check that the vehicle harness is not stuck in the cover.
• Replace the steering column if it has been dropped or sustained an impact.
Installation is in the reverse order of removal.
• For intermediate shaft bolt direction, refer to
.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• After installing steering column, perform self-diagnosis with CON-
SULT to ensure correct operation. Refer to
• Inspect steering column after installation. Refer to
Inspection
INFOID:0000000009385536
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are any
abnormal conditions.
• Measure steering column rotating torque using Tool (A). Replace
steering column if the rotating torque is outside specification
• Measure the steering column length (L) as shown, if vehicle has
been involved in a minor collision. Replace steering column if out-
side specification.
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
SGIA1295E
Tool number
:
—
(J-25765-A)
Rotating torque
.
JPGIA0085ZZ
Steering column length (L) : Refer to
.
JPGIA0111ZZ
STEERING COLUMN
ST-11
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Check each part of steering column for damage or other malfunctions. Replace if there are any abnormal
conditions. Refer to
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt mechanism operating range (T) as shown.
Tilt operating range (T)
: Refer to
JPGIA0043ZZ
ST-12
< REMOVAL AND INSTALLATION >
STEERING SHAFT
STEERING SHAFT
Exploded View
INFOID:0000000009385537
Removal and Installation
INFOID:0000000009385538
REMOVAL
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column and steering gear. Be
sure to secure steering wheel using string to avoid turning.
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the middle position.
CAUTION:
Securely lock the tilt lever.
3. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
4. Loosen lower joint upper bolt.
5. Remove lower joint lower bolt and separate lower joint from the steering gear lower shaft.
CAUTION:
• Place a matching mark on both lower joint and steering gear lower shaft before removing lower
joint.
• When removing lower joint, do not insert any tool into the yoke groove to pull out the lower joint.
Replace the lower joint if damaged.
6. Remove lower joint from steering intermediate shaft.
7. Remove the steering intermediate shaft bolt, from steering column, and remove steering intermediate
shaft from steering column.
CAUTION:
• Place a matching mark on both steering intermediate shaft and steering column before removing
steering intermediate shaft.
• When removing the steering intermediate shaft, do not insert any tool into the yoke groove to
pull out the steering intermediate shaft or damage could occur. Replace the steering intermedi-
ate shaft if damaged.
INSTALLATION
CAUTION:
During installation, finger-tighten all of the bracket and joint retaining bolts; then tighten them to spec-
ification. Do not apply undue stress to the steering column.
Installation is in the reverse order of removal.
1.
Lower joint
2.
Steering intermediate shaft
3.
Steering column
JPGIA0112GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст