Nissan Versa Note. Manual — part 761
STEERING SHAFT
ST-13
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Before installation, check that steering column tilt is in the middle position.
• For intermediate shaft bolt, and lower joint bolt direction, refer to
• To install align the steering gear guide protrusion (A) with the
groove of lower joint (1), make sure the bolt is securely seated in
groove (B) of steering gear before final tightening.
CAUTION:
If a guide protrusion is not included, align with the matching
mark placed at the removal step.
• When tightening lower joint bolt to the steering gear lower shaft,
temporarily tighten it and make sure there is no sticking or galling
before final tightening.
• When connecting intermediate shaft upper side (1) and column
shaft, make sure the bolt is securely seated in groove (A) of col-
umn shaft before final tightening.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009385539
INSPECTION AFTER REMOVAL
• Check each part of steering intermediate shaft, lower joint, and steering column for damage or other mal-
functions. Replace if there are any abnormal conditions.
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
• Check each part of steering intermediate shaft, lower joint, and steering column for damage or other mal-
functions. Replace if there are any abnormal conditions.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check the neutral position of the steering angle sensor. Refer to
JPGIA0041ZZ
SGIA1295E
ST-14
< REMOVAL AND INSTALLATION >
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009385540
Removal and Installation
INFOID:0000000009385541
CAUTION:
• Spiral cable may be cut if steering wheel turns while separating steering column and steering gear;
Always secure the steering wheel using string to avoid turning.
• Place a matching mark on both lower joint and steering gear before removing lower joint.
• When removing lower joint, do not place any tool into the yoke groove to pull out the lower joint.
Replace the lower joint if damaged.
REMOVAL
1. Set the front wheels and tires in the straight-ahead position.
2. Set the steering column tilt to the middle position.
CAUTION:
Securely lock the tilt lever.
3. Remove front suspension member. Refer to
FSU-14, "Removal and Installation"
4. Remove the steering gear bolts and nuts and separate the steering gear from the front suspension mem-
ber.
5. Separate cowl seal from steering gear if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• During installation, finger-tighten all of the bracket and joint retaining bolts; then tighten them to
specification. Do not apply undue stress to the steering column.
• The guide protrusion is not required to be reinstalled.
• Before installation, check that the steering column tilt is in the middle position.
• Clean mating surface on the body side of cowl seal when installing steering gear assembly.
• Inspect steering gear after installation. Refer to
Inspection
INFOID:0000000009385542
INSPECTION AFTER REMOVAL
• Check each part of steering gear for damage or other malfunctions. Replace if there are any abnormal con-
1.
Guide
2.
Cowl seal
3.
Steering gear
4.
Front suspension member
Front
AWGIA0236ZZ
STEERING GEAR AND LINKAGE
ST-15
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
INSPECTION AFTER INSTALLATION
• Rotate steering wheel to make sure it is centered and there is no binding, noise or excessive steering effort.
• Make sure that the number of turns are the same from the straight-ahead position to the left and right locks.
• Check each part of steering system for damage or other malfunctions. Replace if there are any abnormal
conditions.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check wheel alignment. Refer to
• Check the neutral position of the steering angle sensor. Refer to
ST-16
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
UNIT DISASSEMBLY AND ASSEMBLY
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009385543
Disassembly and Assembly
INFOID:0000000009385544
DISASSEMBLY
1. Remove outer socket lock nut and outer socket.
CAUTION:
When loosening outer socket lock nut, be sure to hold outer socket with a suitable tool to prevent
ball joint from contacting knuckle.
2. Remove inner boot clamp, outer boot clamp and remove boot.
CAUTION:
Do not damage inner socket or steering gear housing when removing boot.
3. Remove inner socket.
ASSEMBLY
1. Apply (Autolex A or Dow Corning 111) or equivalent to inner socket and turn pinion fully to retract inner
socket into gear housing assembly.
CAUTION:
Make sure there are no contaminants in the grease, on the inner socket, or inside the steering gear
housing.
1.
Joint cover
2.
Steering gear
3.
Inner socket
4.
Inner boot clamp
5.
Boot
6.
Outer boot clamp
7.
Outer socket
ALGIA0098GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст