Nissan Versa Note. Manual — part 849
WCS-10
< SYSTEM DESCRIPTION >
SYSTEM
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
KEY WARNING CHIME
KEY WARNING CHIME : Key Warning Chime
INFOID:0000000009667997
SYSTEM DIAGRAM
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled.
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
SIGNAL PATH
1. BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line.
Signal name
Signal source
Ignition switch signal
—
Seat belt buckle switch signal (LH) Seat belt buckle switch (LH)
Combination meter
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination meter
AWNIA3130GB
Operation conditions
Ignition switch
OFF or ACC position
Key switch
ON (key is in key cylinder)
Driver side door
Open [front door switch LH ON]
Operation conditions
Ignition switch
ON
Key switch
ON (key is removed from key cylinder)
Driver side door
Close [front door switch LH OFF]
Signal name
Signal source
Ignition switch signal
—
WCS
SYSTEM
WCS-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
2. Combination meter sounds integrated buzzer, when it receives a buzzer output signal from BCM.
Key switch signal
Key switch
BCM
Driver door switch signal
Front door switch LH
BCM
Signal name
Signal source
Buzzer output signal
BCM
Combination meter
Signal name
Signal source
WCS-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000009693749
ON BOARD DIAGNOSIS ITEM
Information display, speedometer and tachometer can be checked in self-diagnosis mode.
STARTING COMBINATION METER SELF-DIAGNOSIS MODE
METHOD OF STARTING
1. Turn ignition switch ON, and switch the trip meter to “trip A” or “trip B”.
2. Turn ignition switch to OFF.
3. While pressing the meter control switch (1), turn the ignition
switch ON.
4. Make sure that the trip meter displays “0000.0”.
5. Press the meter control switch (1) at least 3 times. (Within 7 sec-
onds after the ignition switch is turned ON).
6. The combination meter is turned to self-diagnosis mode.
• All segments of the information display and shift position indi-
cator (A) for CVT models are displayed.
NOTE:
• Check combination meter power supply and ground circuit when the self-diagnosis mode of the combination
meter does not start. replace combination meter if power supply and ground circuit are normal.
• If any of the segments are not displayed, replace combination meter.
7. Each meter activates by pressing the meter control switch.
JSNIA3904ZZ
JSNIA3900ZZ
AWNIA2440ZZ
WCS
DIAGNOSIS SYSTEM (COMBINATION METER)
WCS-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NOTE:
• If any of the meters or gauges is not activated, replace combination meter.
• The figure is reference.
CONSULT Function
INFOID:0000000009693750
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
SELF DIAG RESULT
.
DATA MONITOR
Display Item List
X: Applicable
METER/M&A Diagnosis mode
Description
Self Diagnostic Result
The combination meter self-diagnosis results.
Data Monitor
Displays combination meter input/output data in real time.
Work support
Supports combination meter diagnosis.
Warning History
Lighting history of the warning lamp and indicator lamp can be checked.
Display item [Unit]
MAIN
SIGNALS
Description
SPEED METER
[mph] or [km/h]
X
Displays the value of vehicle speed signal.
SPEED OUTPUT
[mph] or [km/h]
X
Displays the value of vehicle speed signal, which is transmitted to each unit with CAN communication.
ODO OUTPUT
[Mi] or [km]
Displays odometer signal value transmitted to other units via CAN communication.
TACHO METER
[rpm]
X
Displays the value of engine speed signal, which is input from ECM.
FUEL METER
[L]
X
Displays the fuel level.
W TEMP METER
[
°F] or [°C]
X
Displays the value of engine coolant temperature signal, which is input from ECM.
ABS W/L
[ON/OFF]
Displays [ON/OFF] condition of ABS warning indicator
VDC/TCS IND
[ON/OFF]
Displays [ON/OFF] condition of VDC OFF indicator lamp.
SLIP IND
[ON/OFF]
Displays [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L
[ON/OFF]
Displays [ON/OFF] condition of brake warning indicator.
DOOR W/L
[ON/OFF]
Displays [ON/OFF] condition of door warning indicator.
HI-BEAM IND
[ON/OFF]
Displays [ON/OFF] condition of high beam indicator.
TURN IND
[ON/OFF]
Displays [ON/OFF] condition of turn indicator.
FR FOG IND
[ON/OFF]
Displays [ON/OFF] condition of front fog lamp indicator.
LIGHT IND
[ON/OFF]
Displays [ON/OFF] condition of light indicator.
OIL W/L
[ON/OFF]
Displays [ON/OFF] condition of engine oil pressure warning indicator.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст