Nissan Versa Note. Manual — part 706
B2620 PARK/NEUTRAL POSITION SWITCH
SEC-103
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
CHECK PARK/NEUTRAL POSITION SWITCH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect park/neutral position switch connector.
3. Turn ignition switch ON.
4. Check voltage between park/neutral position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK PARK/NEUTRAL POSITION SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Connect park/neutral position switch connector.
3. Turn ignition switch ON.
4. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End
6.
CHECK PARK/NEUTRAL POSITION SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect park/neutral position switch connector.
3. Disconnect BCM connector.
4. Check continuity between park/neutral position switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK PARK/NEUTRAL POSITION SWITCH
SEC-104, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace park/neutral position switch. Refer to
TM-19, "Removal and Installation"
.
(+)
(–)
Voltage (V)
(Approx.)
Park/neutral position switch
Connector
Terminal
F24
1
Ground
Battery voltage
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M98
102
Ground
Shift lever
Neutral position
Battery voltage
Except neutral position
0 – 1.5 V
Park/neutral position switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
F24
2
M98
102
Yes
SEC-104
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2620 PARK/NEUTRAL POSITION SWITCH
8.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End
Component Inspection
INFOID:0000000009705910
1.
CHECK PARK/NEUTRAL POSITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect park/neutral position switch connector.
3. Check continuity between park/neutral position switch terminals.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Replace park/neutral position switch. Refer to
TM-19, "Removal and Installation"
.
Park/neutral position switch
Condition
Continuity
Terminal
1
2
Shift lever
Neutral position
Yes
Except neutral position
No
B26E8 CLUTCH INTERLOCK SWITCH
SEC-105
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B26E8 CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009705911
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1. Turn ignition switch ON.
2. Wait 2 seconds or more under the following conditions.
-
Shift lever: In the neutral position.
-
Clutch pedal: Depressed
3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES >> Go
SEC-105, "Diagnosis Procedure"
.
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1. Release clutch pedal and wait 2 seconds or more.
2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES >> Go
SEC-105, "Diagnosis Procedure"
.
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009705912
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF COMBINATION METER
Check DTC in “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK FUSE
1. Turn power switch OFF.
2. Check that the following fuse in the fuse block (J/B) is not blown.
Is the inspection result normal?
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B26E8
CLUTCH SW
(Clutch switch)
BCM detects the following conditions for 2
seconds or more.
• Clutch pedal position switch: ON
(Clutch pedal is released)
• Clutch interlock switch: ON
(Clutch pedal is depressed)
• Harness or connector
(Clutch interlock switch circuit is
open or shorted)
• Harness or connector
(Clutch pedal position switch circuit
is open or shorted)
• Clutch interlock switch
• Clutch pedal position switch
• BCM
Signal name
Fuse No.
Ignition power supply
10 (10 A)
SEC-106
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B26E8 CLUTCH INTERLOCK SWITCH
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the cause of blowing.
3.
CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY
1. Disconnect clutch interlock switch connector.
2. Turn ignition switch ON.
3. Check voltage between clutch interlock switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK CLUTCH INTERLOCK SWITCH SIGNAL
1. Connect clutch interlock switch connector.
2. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 6.
5.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End
6.
CHECK CLUTCH INTERLOCK SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between clutch interlock switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK CLUTCH INTERLOCK SWITCH
SEC-101, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace clutch interlock switch. Refer to
.
8.
CHECK INTERMITTENT INCIDENT
(+)
(–)
Voltage (V)
(Approx.)
Clutch interlock switch
Connector
Terminal
E34
1
Ground
Battery voltage
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M98
101
Ground
Clutch pedal
Released
6 – 16 V
Depressed
0 – 1.5 V
Clutch interlock switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
E34
2
M98
101
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст