Nissan Versa Note. Manual — part 707
B26E8 CLUTCH INTERLOCK SWITCH
SEC-107
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
GI-41, "Intermittent Incident"
.
>> Inspection End
Component Inspection (Clutch Interlock Switch)
INFOID:0000000009705913
1.
CHECK CLUTCH INTERLOCK SWITCH
1. Turn ignition switch OFF.
2. Disconnect clutch interlock switch connector.
3. Check continuity between clutch interlock switch terminals.
.
Is the inspection result normal?
YES
>> Inspection End
NO
>> Replace clutch interlock switch. Refer to
.
Clutch interlock switch
Condition
Continuity
Terminal
1
2
Clutch pedal
Depressed
Yes
Not depressed
No
SEC-108
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B26F3 STARTER CONTROL RELAY
B26F3 STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009705914
DTC DETECTION LOGIC
NOTE:
• If DTC B26F3 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B26F3 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine.
-
Selector lever: In the P position
-
Brake pedal: Not depressed
2. Wait 2 seconds after engine started.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-108, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705915
1.
CHECK DTC OF IPDM E/R
Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Perform the diagnosis procedure related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26F3
START CONT RLY ON
BCM requests IPDM E/R to turn starter
control relay OFF, but BCM cannot receive
starter control relay OFF state signal from
IPDM E/R (CAN).
• Harness or connectors
(The CAN communication line is open
or shorted.)
• IPDM E/R
B26F4 STARTER CONTROL RELAY
SEC-109
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B26F4 STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009705916
DTC DETECTION LOGIC
NOTE:
• If DTC B26F4 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B26F4 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or
more.
-
Selector lever: In the P position
-
Brake pedal: Not depressed
2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-109, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705917
1.
CHECK DTC OF IPDM E/R
Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Perform the diagnosis procedure related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26F4
START CONT RLY OFF
BCM requests IPDM E/R to turn starter
control relay ON, but BCM cannot receive
starter control relay ON state signal from
IPDM E/R (CAN).
• Harness or connectors
(The CAN communication line is open
or shorted.)
• IPDM E/R
SEC-110
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B26F7 BCM
B26F7 BCM
DTC Logic
INFOID:0000000009705918
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press door request switch.
2. Turn ignition switch ON.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-110, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705919
1.
INSPECTION START
1. Turn ignition switch ON.
2. Select Self Diagnostic Result mode of BCM using CONSULT.
3. Touch ERASE.
4. Perform DTC CONFIRMATION PROCEDURE for DTC B26F7. Refer to
.
Is DTC B26F7 detected again?
YES
>> GO TO 2.
NO
>> Inspection End.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26F7
BCM
Inside key antenna output circuit in BCM is malfunctioning. BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст