Nissan Versa Note. Manual — part 252
REAR DOOR LOCK
DLK-293
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolts.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with inside handle and outside handle bracket.
• Check door lock assembly for poor lubrication. If necessary,
apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009645209
REMOVAL
1. Remove rear door finisher. Refer to
INT-18, "Removal and Installation"
.
2. Remove upper portion of vapor barrier. Refer to
.
3. Release lock knob (2) and inside handle cable (3) from clip (1)
using a suitable tool.
4. Remove inside handle bolt.
5. Release inside handle (1) from door panel using a suitable tool
and remove.
: Pawl
JMKIA8087ZZ
JMKIA5704ZZ
AWKIA2500ZZ
DLK-294
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009645210
REMOVAL
1. Remove inside handle. Refer to
DLK-293, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to
remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
REAR DOOR LOCK
DLK-295
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Remove front gasket and rear gasket.
6. Slide outside handle bracket toward rear of vehicle to remove.
: Front
7. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA5890ZZ
JMKIA5891ZZ
DLK-296
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000009645211
BACK DOOR LOCK
BACK DOOR LOCK : Removal and Installation
INFOID:0000000009645212
REMOVAL
1. Remove back door inner finisher. Refer to
INT-36, "BACK DOOR INNER FINISHER : Removal and Instal-
.
2. Remove back door outer finisher. Refer to
EXT-46, "Removal and Installation"
3. Disconnect lock rod from key cylinder (if equipped).
4. Disconnect the harness connectors from the back door lock.
5. Disconnect door lock cable from handle.
6. Remove back door lock bolts and back door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten back door bolts to specification.
• After installation, check back door open/close and lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009645213
REMOVAL
1. Remove back door outer finisher. Refer to
EXT-46, "Removal and Installation"
2. Release the back door lock cable from the outside handle.
3. Remove outside handle bolts and outside handle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
1.
Outside handle
2.
Back door lock cable
3.
Back door lock actuator
4.
Back door lock
5.
Door striker
6.
Key cylinder rod clip (if equipped)
7.
Key cylinder rod bracket (if equipped) 8.
Key cylinder rod (if equipped)
AWKIA2576ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст