Nissan Versa Note. Manual — part 430
EXL-104
< REMOVAL AND INSTALLATION >
HAZARD SWITCH
HAZARD SWITCH
Exploded View
INFOID:0000000008969404
Removal and Installation
INFOID:0000000009445881
REMOVAL
1. Remove cluster lid C. Refer to
IP-22, "Removal and Installation"
2. Release pawls and remove hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
1. Cluster lid C
2. Hazard switch
Pawl
AWLIA2163ZZ
REAR COMBINATION LAMP
EXL-105
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR COMBINATION LAMP
Exploded View
INFOID:0000000008969409
Removal and Installation
INFOID:0000000008969410
REMOVAL
1. Remove rear combination lamp bolts.
2. Release the locating pin (A) of the rear combination lamp using
a suitable tool (B) as shown.
3. Disconnect the harness connector from the rear combination lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000008969411
WARNING:
Do not touch bulb with bare hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-105, "Removal and Installation"
1.
Rear combination lamp
A.
Grommet
B.
Clip
Locating pin
AWLIA2167ZZ
AWLIA2169ZZ
EXL-106
< REMOVAL AND INSTALLATION >
REAR COMBINATION LAMP
2. Rotate stop/tail lamp bulb socket counterclockwise and remove.
3. Remove stop/tail lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
REAR TURN SIGNAL LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-105, "Removal and Installation"
2. Rotate rear turn signal lamp bulb socket counterclockwise and remove.
3. Remove rear turn signal lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
BACK-UP LAMP BULB
Removal
1. Remove rear combination lamp. Refer to
EXL-105, "Removal and Installation"
2. Rotate back-up lamp bulb socket counterclockwise and remove.
3. Remove back-up lamp bulb from bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, install bulb socket securely for watertightness.
HIGH-MOUNTED STOP LAMP
EXL-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000008969412
Removal and Installation
INFOID:0000000008969413
REMOVAL
1. Release high-mounted stop lamp pawls using a suitable tool.
2. Disconnect the harness connector from high-mounted stop lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb Replacement
INFOID:0000000008969414
HIGH-MOUNTED STOP LAMP BULB
The high-mounted stop lamp bulb is a LED and is integrated into the high-mounted stop lamp and is serviced
as an assembly. Refer to
EXL-107, "Removal and Installation"
1.
High-mounted stop lamp
2.
High-mounted stop lamp LED
Pawl
AWLIA2164ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст