Nissan Frontier D22. Manual — part 165
FRONT DISC BRAKE
BR-27
C
D
E
G
H
I
J
K
L
M
A
B
BR
3.
Bleed air. Refer to
BR-10, "Bleeding Brake System"
Caliper Disassembly and Assembly
EFS003FX
DISASSEMBLY
WARNING:
Do not place your fingers in front of piston.
CAUTION:
●
Do not scratch or score cylinder wall.
●
CL28VD type front disc brake uses plastic pistons. Handle them carefully.
1.
Push out piston and dust covers with compressed air. Use a
wooden block so that both pistons come out evenly.
2.
Remove piston seal with a suitable tool.
INSPECTION AFTER DISASSEMBLY
Cylinder Body
●
Check inside surface of cylinder for score, rust, wear, damage and presence of foreign objects. If any of
the above conditions are observed, replace cylinder body.
●
Minor damage from rust or foreign objects may be eliminated by polishing surface with a fine emery paper.
Replace cylinder body if necessary.
CAUTION:
Use brake fluid to clean. Never use mineral oil.
Piston
CAUTION:
Piston sliding surface is plated. Do not polish with emery paper
even if rust or foreign objects are stuck to sliding surface.
Main Pin, Main Pin Bolt and Pin Boot
Check for wear, cracks, rust and other damage. Replace if any of the above conditions are observed.
SBR085A
SBR177C
BR-28
FRONT DISC BRAKE
DISC ROTOR INSPECTION
Runout
1.
Check rotor runout using a dial indicator.
Make sure that wheel bearing axial end play is within the speci-
fications before measuring. Refer to
2.
If the rotor runout is out of specification, find minimum rotor
runout position as follows:
a.
Remove nuts and rotor from wheel hub.
b.
Shift the rotor one hole and secure rotor to wheel hub with nuts.
c.
Measure runout.
d.
Repeat steps a. to c. so that minimum rotor runout position can be found.
3.
If the rotor runout is still out of specification, turn rotor with on-car brake lathe (“MAD, DL-8700”, “AMMCO
700 and 705” or equivalent).
Thickness
If thickness variation exceeds the specification, turn rotor with on-car
brake lathe.
ASSEMBLY
1.
Insert piston seal into groove on cylinder body.
2.
With piston boot fitted to piston, insert piston boot into groove on
cylinder body and install piston.
3.
Properly secure piston boot.
CAUTION:
●
Secure dust seal properly.
●
Lubricate with new brake fluid before installing pistons
into cylinder body.
Maximum rotor runout
: 0.07 mm (0.0028 in)
SBR089A
Thickness variation (At
least 8 positions)
: Maximum 0.02 mm
(0.0008 in)
Rotor repair limit
KA24DE model
: 24.0 mm (0.945 in)
VG33E and VG33ER models
: 26.0 mm (1.024 in)
SBR090A
SBR178C
SBR179CA
FRONT DISC BRAKE
BR-29
C
D
E
G
H
I
J
K
L
M
A
B
BR
Brake Burnishing Procedure
EFS003FY
Burnish the brake contact surfaces according to the following procedure after refinishing or replacing drums or
rotors, after replacing pads or linings, or if a soft pedal occurs at very low mileage.
CAUTION:
Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1.
Drive the vehicle on a straight smooth road at 50 km/h (31 MPH).
2.
Use medium brake pedal/foot effort to bring the vehicle to a complete stop from 50 km/h (31 MPH). Adjust
brake pedal/foot pressure such that vehicle stopping time equals 3 to 5 seconds.
3.
To cool the brake system, drive the vehicle at 50 km/h (31 MPH) for 1 minute without stopping.
4.
Repeat steps 1 to 3, 10 times or more to complete the burnishing procedure.
BR-30
REAR DRUM BRAKE
REAR DRUM BRAKE
PFP:43206
Components
EFS003FZ
1.
Shoe hold pin
2.
Plug
3.
Shoe hold pin
4.
Back plate
5.
Air bleeder cap
6.
Air bleeder
7.
Cylinder body
8.
Piston cup
9.
Piston
10.
Dust cover
11.
Spring
12.
Wheel cylinder
13.
Pin
14. Adjusting lever
15.
Toggle lever
16.
Washer
17. Retainer clip
18.
Retainer spring
19.
Spring seat
20. Shoe hold spring
21.
Retainer
22.
Shoe (leading side)
23. Adjuster
24.
Shoe (trailing side)
WFIA0133E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст