Nissan Frontier D22. Manual — part 164
VACUUM PIPING
BR-23
C
D
E
G
H
I
J
K
L
M
A
B
BR
VACUUM PIPING
PFP:47474
Vacuum Hose
EFS003FR
Removal and Installation
EFS003FS
CAUTION:
When installing vacuum hoses, pay attention to the following points.
●
Do not apply any oil or lubricants to vacuum hose with
check valve.
●
Insert vacuum tube into vacuum hose as shown.
●
Install vacuum hose with internal check valve, paying atten-
tion to its direction.
LBR159
SBR225B
BR-24
VACUUM PIPING
Inspection
EFS003FT
HOSES AND CONNECTORS
Check vacuum lines and connections for airtightness, improper attachment, chafing and deterioration.
CHECK VALVE
Check vacuum with a vacuum pump.
Connect to booster side
Vacuum should exist.
Connect to engine side
Vacuum should not exist.
SBR844B
FRONT DISC BRAKE
BR-25
C
D
E
G
H
I
J
K
L
M
A
B
BR
FRONT DISC BRAKE
PFP:41000
Components
EFS003FU
Pad Replacement
EFS003FV
WARNING:
Clean brakes with a vacuum dust collector to minimize the hazard of airborne particles or other mate-
rials.
CAUTION:
●
When cylinder body is open, do not depress brake pedal, or piston will pop out.
●
Be careful not to damage piston boot or get oil on rotor. Always replace shims when replacing
pads.
●
If shims are rusted or show peeling of the rubber coat, replace them with new shims.
●
It is not necessary to remove connecting bolt except for disassembly or replacement of caliper
assembly. In this case, suspend cylinder body with wire so as not to stretch brake hose.
●
Burnish the brake contact surfaces after refinishing or replacing drums or rotors, after replacing
pads or linings, or if a soft pedal occurs at very low mileage. Refer to
1.
Remove reservoir cap.
2.
Remove lower main pin bolt.
1.
Main pin
2.
Pin boot
3.
Torque member fixing bolt
4.
Torque member
5.
Shim cover (if equipped)
6.
Inner shim
7.
Inner pad
8.
Pad retainer
9.
Outer pad
10. Outer shim
11.
Connecting bolt
12. Copper washer
13. Main pin bolt
14.
Bleed valve
15. Cylinder body
16. Piston seal
17.
Piston
18. Piston boot
WBR313
SBR081A
BR-26
FRONT DISC BRAKE
3.
Rotate cylinder body upward. Remove pad retainers, inner and
outer shims and shim cover (if equipped).
CAUTION:
Carefully monitor brake fluid level because brake fluid will
return to reservoir tank when pushing back pistons.
Caliper Removal and Installation
EFS003FW
REMOVAL
WARNING:
Clean brake pads with a vacuum dust collector to minimize the hazard of airborne particles or other
materials.
CAUTION:
Suspend caliper assembly with wire so as not to stretch brake hose.
Remove torque member fixing bolts and connecting bolt.
NOTE:
It is not necessary to remove connecting bolt except for disassembly
or replacement of caliper assembly. In this case, suspend caliper
assembly with wire so as not to stretch brake hose.
INSTALLATION
CAUTION:
●
Refill with new brake fluid “DOT 3”.
●
Never reuse drained brake fluid.
1.
Install caliper assembly.
2.
Install brake hose to caliper securely.
Standard pad thickness
: 10 mm (0.39 in)
Pad wear limit
: 2.0 mm (0.079 in)
SBR010B
SBR083A
Torque member fixing bolts
KA24DE models
: 72 - 97 N·m (7.3 - 9.9 kg-m,
53 - 72 ft-lb)
VG33E and VG33ER
models
: 133 - 177 N·m (14 - 18 kg-m,
101 - 130 lb-ft)
Connecting bolt
: 17 - 20 N·m (1.8 - 2.0 kg-m,
13 - 14 lb-ft)
SBR084A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст