Nissan Frontier D22. Manual — part 350
DTC P1490 VACUUM CUT VALVE BYPASS VALVE
EC-503
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
UBS00DC5
BBWA1067E
EC-504
[KA24DE]
DTC P1490 VACUUM CUT VALVE BYPASS VALVE
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
UBS00DC6
1.
INSPECTION START
Do you have CONSULT-II?
Yes or No
Yes
>> GO TO 2.
No
>> GO TO 3.
2.
CHECK VACUUM CUT VALVE BYPASS VALVE CIRCUIT
1.
Turn ignition switch ON.
2.
Perform “VC/V BYPASS/V” in “ACTIVE TEST” mode.
3.
Make sure that clicking sound is heard from the vacuum cut
valve bypass valve.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 3.
TER-
MINAL
NO.
WIRE
COLO
R
ITEM
CONDITION
DATA (DC Voltage)
120
P/B
Vacuum cut valve bypass
valve
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14V)
SEF806Y
DTC P1490 VACUUM CUT VALVE BYPASS VALVE
EC-505
[KA24DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
3.
CHECK POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect vacuum cut valve bypass valve harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between terminal 2 and ground with CONSULT-II
or tester.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E43, M65
●
Harness connectors M67, C1
●
Fuse block (J/B) connector E49
●
10A fuse
●
Harness for open or short between vacuum cut valve bypass valve and fuse
>> Repair harness or connectors.
5.
CHECK OUTPUT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 120 and vacuum cut valve bypass valve terminal 1.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 7.
NG
>> GO TO 6.
SEF186S
Voltage
: Battery voltage
SEF192V
Continuity should exist.
EC-506
[KA24DE]
DTC P1490 VACUUM CUT VALVE BYPASS VALVE
6.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors M67, C1
●
Harness connectors M81, F36
●
Harness for open or short between vacuum cut valve bypass valve and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK VACUUM CUT VALVE BYPASS VALVE
With CONSULT-II
Check air passage continuity.
Perform “VC/V BYPASS/V” in “ACTIVE TEST” mode.
Without CONSULT-II
Check air passage continuity shown in the figure.
OK or NG
OK
>> GO TO 8.
NG
>> Replace vacuum cut valve bypass valve.
8.
CHECK INTERMITTENT INCIDENT
EC-120, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
>> INSPECTION END
SEF807Y
SEF557Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст