Nissan Frontier D22. Manual — part 175
TROUBLE DIAGNOSIS
BRC-31
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
–:Not applicable
ACTIVE TEST
Operation Procedure
CAUTION:
●
Do not perform active test while driving the vehicle.
●
Make sure to completely bleed air from brake system.
●
Active test cannot be performed when ABS warning lamp is on.
1.
Connect the CONSULT-II connector to the data link connector and start the engine.
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
2.
Touch
″START″ on the display.
3.
Touch
″ABS″ and ″ACTIVE TEST″.
4.
Test item selection screen is displayed.
5.
Touch necessary test item.
6.
Touch
″START″.
7.
Carry out the active test by touching screen key.
Solenoid Valve
1.
To perform active test of ABS functions, select major items for
each test item.
2.
For ABS solenoid valve, touch “UP”, “KEEP” and “DOWN”. For
ABS solenoid valve (ACT), touch “UP,” “ACTUATOR UP” and
“ACTUATOR KEEP”. Use screen monitor to check that solenoid
valve operates as shown in Solenoid Valve Operation Chart.
Refer to
BRC-88, "Solenoid Valve Operation Chart"
.
Solenoid Valve Operation Chart
WFIA0043E
LBR379
LFIA0180E
Operation
ABS solenoid valve
ABS solenoid valve (ACT)
UP
KEEP
DOWN
UP
ACT UP
ACT KEEP
FR RH SOL
FR RH ABS SOLE-
NOID (ACT)
FR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR RH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
BRC-32
[ABS]
TROUBLE DIAGNOSIS
*: ON for 1 to 2 seconds after the touch, and then OFF
NOTE:
●
If active test is performed with brake pedal depressed, pedal stroke may change. This is normal.
●
“TEST IS STOPPED” is displayed approximately 10 seconds after operation starts.
●
After “TEST IS STOPPED” is displayed, to perform test again, repeat Active Test Step 6.
ABS Motor
Touch “ON” and “OFF” on the screen. Check that ABS motor relay
operates as shown in table below.
NOTE:
●
If active test is performed with brake pedal depressed, pedal
stroke may change. This is normal.
●
“TEST IS STOPPED” is displayed approximately 10 seconds
after operation starts.
FR LH SOL
FR LH ABS SOLE-
NOID (ACT)
FR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
FR LH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
RR RH SOL
RR RH ABS SOLE-
NOID (ACT)
RR RH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR RH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
RR LH SOL
RR LH ABS SOLE-
NOID (ACT)
RR LH IN SOL
OFF
ON
ON
OFF
OFF
OFF
RR LH OUT SOL
OFF
OFF
ON*
OFF
OFF
OFF
Operation
ABS solenoid valve
ABS solenoid valve (ACT)
UP
KEEP
DOWN
UP
ACT UP
ACT KEEP
Operation
ON
OFF
ABS actuator relay
ON
ON
ABS motor relay
ON
OFF
SFIA0593E
TROUBLE DIAGNOSIS
BRC-33
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
For Fast and Accurate Diagnosis
EFS003GW
PRECAUTIONS FOR DIAGNOSIS
●
Before performing diagnosis, always read precautions. Refer to
●
When replacing ABS actuator and electric unit (control unit), be sure labels on control units are the same
color.
●
After diagnosis is finished, be sure to erase memory. Refer to
●
When checking continuity and voltage between units, be sure to check for disconnection, looseness,
bend, or collapse of connector terminals. If any non-standard condition is found, repair or replace connec-
tor terminals.
●
For intermittent symptoms, possible cause is malfunction in harness, harness connector, or terminals.
Move harness, harness connector, and terminals to check for poor connections.
●
If a circuit tester is used for the check, be careful not to forcibly extend any connector terminal.
●
To use CONSULT-II to perform self-diagnosis of ABS actuator and electric unit (control unit), active tests,
or work support, first stop work, then connect CONSULT-II and select “ABS”.
●
CONSULT-II self-diagnosis results are displayed without regard to occurrence timing. In some cases later
ones (timing value is small) appear on the next screen.
●
While self-diagnosis results of CONSULT-II shows an error, if CONSULT-II active test is performed, an
engine system error may be indicated. In this case, start engine to resume the normal screen.
●
The following symptoms may be caused by normal operations:
ON and OFF Timing for ABS Warning Lamp
×: ON
–: OFF
Symptom
Symptom description
Result
Motor operation noise
This is noise of motor inside ABS actuator. Slight noise may occur dur-
ing ABS operation.
Normal
When the vehicle speed goes over 20 km/h (12.5 mph), the motor and
valves operating noise may be heard. It happens only once after IGN
(ignition) is ON. This is a normal status of the system operation check.
System operation check
noise
When the engine starts, slight “click” noise may be heard from engine
compartment. This is normal and is part of system operation check.
Normal
ABS operation (Longer stop-
ping distance)
On roads with low friction coefficients, such as snowy roads or gravel
roads, vehicles with ABS may require a longer stopping distance. There-
fore, when driving on such roads, avoid overconfidence and keep speed
sufficiently low.
Normal
Condition
ABS warning lamp
Remarks
Ignition SW OFF
–
—
For approx. 2 seconds after ignition SW is
turned ON
×
—
Approx. 2 seconds after ignition switch ON
–
Turns OFF 2 seconds after ignition switch ON.
There is an ABS
error.
×
—
×
There is an ABS actuator and electric unit (control
unit) error. (Power or ground malfunction)
BRC-34
[ABS]
TROUBLE DIAGNOSIS
Basic Inspection
EFS003GX
BASIC INSPECTION 1: BRAKE FLUID LEVEL AND LEAK INSPECTION
1.
Check fluid level in the brake reservoir tank. If fluid level is low, refill the brake fluid.
2.
Check for leakage in brake piping and around ABS actuator. If leakage or seepage is found, check as fol-
lows.
●
If ABS actuator and electric unit (control unit) connector is loose, tighten piping to specified torque.
Then inspect again and confirm that there is no leakage.
●
If connection of flare nuts or screws of ABS actuator are damaged, replace damaged parts. Then
inspect again and confirm that there is no leakage.
●
If there is leakage or seepage at any location other than ABS actuator connections, wipe away leakage
or seepage with clean cloth. Then inspect again and confirm that there is no leakage.
●
If there is leakage from ABS actuator, wipe away leakage or seepage with clean cloth. Then inspect
again. If there is leakage or seepage, replace ABS actuator unit.
CAUTION:
ABS actuator body cannot be disassembled.
3.
Check brake disc rotor and pads and brake drum and linings. Refer to
.
BASIC INSPECTION 2: INSPECTION FOR LOOSENESS OF POWER SYSTEM TERMINALS
Check battery for looseness on the battery positive/negative terminals and ground connection. If looseness is
detected, tighten the cables to the specified torque. Check that the battery voltage does not drop and the gen-
erator is normal.
BASIC INSPECTION 3: INSPECTION OF ABS WARNING LAMP
1.
Check that ABS warning lamp illuminates for approximately 2 seconds when ignition switch is turned ON.
If it does not illuminate, inspect ABS warning lamp and circuit, and inspect combination meter. Refer to
.
Symptom Chart
EFS003GY
Symptom
Malfunctioning part
Reference
page
ABS works frequently
—
Unexpected pedal reaction
—
Long stopping distance
—
ABS does not work
—
Pedal vibration and noise
—
ABS warning lamp does not illuminate
●
Fuse
●
Combination meter
●
Circuit(s)
●
ABS actuator and electric unit (control unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст