Nissan Frontier D22. Manual — part 200
REMOVAL AND INSTALLATION
BRC-131
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
Yaw Rate/Side/Decel G Sensor
EFS003JB
Always replace sensor if bumped or dropped. Otherwise, performance characteristics of sensor will
be changed, which in turn changes ABS control performance characteristics.
CAUTION:
Do not exceed 9 N·m (0.9 kg-m, 80 in-lb) total tightening torque.
Steering Angle Sensor
EFS003JC
CAUTION:
The steering angle sensor must be adjusted after the spiral cable has been removed and reinstalled or
replaced with a new one. Refer to
BRC-55, "Adjustment of Steering Angle Sensor Neutral Position"
.
The steering angle sensor is built into the spiral cable. For removal and installation procedures, refer to
42, "DRIVER AIR BAG MODULE AND SPIRAL CABLE"
CAN-LAN Converter (CLC)
EFS003JD
1.
Disconnect battery cable.
2.
Remove steering column cover.
3.
Remove instrument lower panel driver side. Refer to
IP-10, "Removal and Installation"
.
4.
Place ASCD control unit aside.
5.
Disconnect CLC harness connector.
6.
Remove bolt and then remove CLC.
Tightening torque:
Step 1
: 7 N·m (0.7 kg-m, 62 in-lb)
Step 2
: 9 N·m (0.9 kg-m, 80 in-lb)
LFIA0134E
LFIA0194E
BRC-132
[VDC/TCS/ABS]
REMOVAL AND INSTALLATION
CL-1
CLUTCH
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION
A
B
CL
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions . . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
CLUTCH SYSTEM — HYDRAULIC TYPE . . . . . 5
Components . . . . . . . . . . . . . . . . 5
Inspection and Adjustment . . . . . . . . . ... 6
CLUTCH MASTER CYLINDER . . . . . . . . .. 8
OPERATING CYLINDER . . . . . . . . . . . 9
Components . . . . . . . . . . . . . . . . 9
Inspection . . . . . . . . . . . . . . . . . 9
CLUTCH RELEASE MECHANISM . . . . . . ... 10
Components . . . . . . . . . . . . . . ... 10
Removal and Installation . . . . . . . . . . 10
Inspection . . . . . . . . . . . . . . . ... 11
Lubrication . . . . . . . . . . . . . . . .. 11
CLUTCH DISC, CLUTCH COVER AND FLYWHEEL ... 12
Components . . . . . . . . . . . . . . ... 12
Inspection and Adjustment . . . . . . . . . . 12
CLUTCH DISC . . . . . . . . . . . . . 12
CLUTCH COVER AND FLYWHEEL . . . . ... 13
FLYWHEEL INSPECTION . . . . . . . . .. 13
Installation . . . . . . . . . . . . . . . .. 13
CL-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Precautions
ECS007GL
●
Recommended fluid is brake fluid “DOT 3”.
●
Never reuse drained brake fluid.
●
Be careful not to splash brake fluid on painted areas.
●
When removing and installing clutch piping, use Tool.
●
Use new brake fluid to clean or wash all parts of master cyl-
inder, operating cylinder and clutch damper.
●
Never use mineral oils such as gasoline or kerosene. It will
ruin the rubber parts of the hydraulic system.
WARNING:
After cleaning the clutch disc, wipe it with a dust collector. Do
not use compressed air.
SBR686C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст