Qashqai J11. Body Control System — part 4
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-49
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
Monitor Item
Condition
BCS-50
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-51
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 5)
INFOID:0000000010699332
WORK SUPPORT
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
BCS-52
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANSWER BACK
Reminder function (door request switch and Intelligent Key) mode can be selected from the
following with this mode
• On: S mode (buzzer or horn reminder non-operation)
• Off: C mode (buzzer or horn operate)
ANSWER BACK I-KEY LOCK UN-
LOCK
Reminder function (door request switch) mode can be selected from the following with this
mode
• BUZZER: Sound Intelligent Key warning buzzer
• HORN: Sound horn
• Off: Only hazard warning lamp operate
• INVALID: This item is displayed, but cannot be used
ANSWER BACK KEYLESS LOCK
UNLOCK
Reminder function (Intelligent Key) mode can be selected from the following with this mode
• On: Horn and hazard warning lamp operate
• Off: Only hazard warning lamp operate
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-53
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
Monitor Item
Condition
BCS-54
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANICE ALARM signal from Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-55
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
BCS-56
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000010378007
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
BCM
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT/AUTO switch in combination switch judged by BCM with the com-
bination switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
RR WIPER ON
[Off/On]
Displays the status of the RR WIPER ON switch in combination switch judged by BCM with the combination
switch reading function.
RR WIPER INT
[Off/On]
Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
RR WASHER SW
[Off/On]
Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW
[Off/On]
Displays the status of the HEADLAMP switch in combination switch judged by BCM with the combination
switch reading function.
LIGHT OFF SW
[Off/On]
Displays the status of the LIGHT OFF switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
RR FOG SW
[Off/On]
Displays the status of the RR FOG switch in combination switch judged by BCM with the combination switch
reading function.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-57
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000010378008
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU) (With Intelligent Key System)
INFOID:0000000010505165
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
WORK SUPPORT
ACTIVE TEST
IMMU : CONSULT Function (BCM - IMMU) (Without Intelligent Key System)
INFOID:0000000010505166
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
WORK SUPPORT
ACTIVE TEST
BATTERY SAVER
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
AUTO ACC FNCTN (AU-
DIO/NAVI SET AFTER IGN
OFF)
Switches the operation of audio and navigation systems between continuous and not continuous after
ignition is OFF.
Monitor item
Content
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen touched.
Monitor item
Content
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen touched.
BCS-58
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000010505178
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TRUNK
TRUNK : Information
INFOID:0000000010699366
Check the vehicle type to use the service information in this section.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
CDL LOCK SW
[On/Off]
Indicated [On/Off] condition of lock signal from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door lock and unlock switch
KEY CYL LK-SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
KEY SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
Service information
Destination
Type 1
For Europe
With Intelligent Key and super lock
Type 2
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
With Intelligent Key, without super lock
Type 3
For Europe
Without Intelligent Key, with super lock
Type 4
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
Without Intelligent Key and super lock
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-59
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TRUNK : CONSULT Function (BCM - TRUNK) (Type 1)
INFOID:0000000010505218
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TRUNK : CONSULT Function (BCM - TRUNK) (Type 2)
INFOID:0000000010505219
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Type 5
• For Australia
• For General export
With Intelligent Key, without super lock
Type 6
• For Australia
• For General export
Without Intelligent Key and super lock
Service information
Destination
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
DETECTION SENSOR (BK)
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
DETECTION SENSOR (BK)
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
BCS-60
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
TRUNK : CONSULT Function (BCM - TRUNK) (Type 3)
INFOID:0000000010505220
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TRUNK : CONSULT Function (BCM - TRUNK) (Type 4)
INFOID:0000000010505221
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TRUNK : CONSULT Function (BCM - TRUNK) (Type 5)
INFOID:0000000010699367
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Contents
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
DETECTION SENSOR (BK)
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-61
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TRUNK : CONSULT Function (BCM - TRUNK) (Type 6)
INFOID:0000000010699368
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT) (With Intelligent Key System)
INFOID:0000000010505163
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Contents
Monitor Item
Contents
STARTER CUT RELAY
Indicates [On/Off] condition of starter control relay
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored
TRUNK LID OPENER SW
NOTE:
This item is displayed, but cannot be monitored
BACK DOOR OEPENR SW
Indicates [On/Off] condition of back door opener switch
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
NOTE:
This item is indicated, but not monitored.
BCS-62
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
ACTIVE TEST
THEFT ALM : CONSULT Function (BCM - THEFT) (Without Intelligent Key System)
INFOID:0000000010505164
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
KEY CYL UN-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL SW-TR
NOTE:
This item is indicated, but not monitored.
SEN CANCEL SW
Indicates [ON/OFF] condition of sensor cancel switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is indicated, but not monitored.
KEY SW
NOTE:
This item is indicated, but not monitored.
Monitored Item
Description
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change vehicle security alarm ON-OFF setting.
SIREN SET
Select the siren function ON or OFF, and siren type.
• MODE 1: Without siren
• MODE 2: With siren
• MODE 3: With external complete protection (with siren)
• MODE 4: Without any external protection (with siren)
• MODE 5: Without external tilt protection (with siren)
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
SIREN
Activates the self-diagnosis function for siren control unit.
VEHICLE SECURITY HORN
NOTE:
This item is indicated, but not used
HEAD LAMP
NOTE:
This item is indicated, but not used
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-63
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
WORK SUPPORT
ACTIVE TEST
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000010378015
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL UN-SW
NOTE:
This item is indicated, but not monitored.
KEY CYL SW-TR
NOTE:
This item is indicated, but not monitored.
SEN CANCEL SW
Indicates [ON/OFF] condition of sensor cancel switch.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is indicated, but not monitored.
KEY SW
NOTE:
This item is indicated, but not monitored.
Monitored Item
Description
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change vehicle security alarm ON-OFF setting.
SIREN SET
Select the siren function ON or OFF, and siren type.
• MODE 1: Without siren
• MODE 2: With siren
• MODE 3: With external complete protection (with siren)
• MODE 4: Without any external protection (with siren)
• MODE 5: Without external tilt protection (with siren)
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
SIREN
Activates the self-diagnosis function for siren control unit.
VEHICLE SECURITY HORN
NOTE:
This item is indicated, but not used
HEAD LAMP
NOTE:
This item is indicated, but not used
Monitor item [UNIT]
Description
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch (push switch) judged by BCM.
BCS-64
< ECU DIAGNOSIS INFORMATION >
BCM
ECU DIAGNOSIS INFORMATION
BCM
Reference Value
INFOID:0000000010378017
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT MONITOR ITEM
Monitor Item
Condition
Value/Status
CONFRM ID ALL
The Intelligent Key ID that the NATS antenna amp. receives is not recog-
nized by any Intelligent Key ID registered to BCM.
Yet
The Intelligent Key ID that the NATS antenna amp. receives is recognized
by any Intelligent Key ID registered to BCM.
Done
CONFIRM ID4
The Intelligent Key ID that the NATS antenna amp. receives is not recog-
nized by the fourth Intelligent Key ID registered to BCM.
Yet
The Intelligent Key ID that the NATS antenna amp. receives is recognized
by the fourth Intelligent Key ID registered to BCM.
Done
CONFIRM ID3
The Intelligent Key ID that the NATS antenna amp. receives is not recog-
nized by the third Intelligent Key ID registered to BCM.
Yet
The Intelligent Key ID that the NATS antenna amp. receives is recognized
by the third Intelligent Key ID registered to BCM.
Done
CONFIRM ID2
The Intelligent Key ID that the NATS antenna amp. receives is not recog-
nized by the second Intelligent Key ID registered to BCM.
Yet
The Intelligent Key ID that the NATS antenna amp. receives is recognized
by the second Intelligent Key ID registered to BCM.
Done
CONFIRM ID1
The Intelligent Key ID that the NATS antenna amp. receives is not recog-
nized by the first Intelligent Key ID registered to BCM.
Yet
The Intelligent Key ID that the NATS antenna amp. receives is recognized
by the first Intelligent Key ID registered to BCM.
Done
NOT REGISTERED
BCM detects registered Intelligent Key ID, or BCM does not detect Intelli-
gent Key ID.
ID OK
BCM detects non-registration Intelligent Key ID.
ID NG
TP 4
The ID of fourth Intelligent Key is not registered to BCM
Yet
The ID of fourth Intelligent Key is registered to BCM
Done
TP 3
The ID of third Intelligent Key is not registered to BCM
Yet
The ID of third Intelligent Key is registered to BCM
Done
TP 2
The ID of second Intelligent Key is not registered to BCM
Yet
The ID of second Intelligent Key is registered to BCM
Done
TP 1
The ID of first Intelligent Key is not registered to BCM
Yet
The ID of first Intelligent Key is registered to BCM
Done
REQ SW -DR
Driver door request switch is not pressed
Off
Driver door request switch is pressed
On
REQ SW -AS
Passenger door request switch is not pressed
Off
Passenger door request switch is pressed
On
REQ SW -BD/TR
Trunk lid opener request switch is not pressed
Off
Trunk lid opener request switch is pressed
On
PUSH SW
Push-button ignition switch (push switch) is not pressed
Off
Push-button ignition switch (push switch) is pressed
On
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст