Qashqai J11. Body Control System — part 3
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-33
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000010505180
WORK SUPPORT
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from keyfob
KEY SW
Indicates [On/Off] condition of key switch
IGN SW
Indicates [On/Off] condition of ignition switch in ON position
START SW
Indicates [On/Off] condition of ignition switch in START position
Monitor Item
Condition
Test item
Description
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operates
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR+5
NOTE:
This item is indicated, but not monitored
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is indicated, but not monitored
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation
BCS-34
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER) (With Intelligent Key System)
INFOID:0000000010505191
DATA MONITOR
ACTIVE TEST
BUZZER : CONSULT Function (BCM - BUZZER) (Without Intelligent Key System)
INFOID:0000000010505192
DATA MONITOR
Service item
Setting item
Description
SET R-DEF TIMER
MODE1
*
NOTE:
Do not use this function.
MODE2
MODE3
Monitor Item
Description
PUSH SW
Indicates [On/Off] condition of push switch
REAR DEF SW
Displays “Press (On)/other (Off)” status determined with the rear window defogger switch
Test Item
Description
REAR DEFOGGER
Rear window defogger operates when “On” on CONSULT screen is touched
Monitor Item [Unit]
Description
PUSH -SW [On/Off]
Indicates condition of push-button ignition switch.
VEH SPEED 1 [km/h]
Indicates vehicle speed signal received from ABS on CAN communication line.
TAIL LAMP SW [On/Off]
Indicates condition of combination switch.
FR FOG SW [On/Off]
Indicates condition of front fog lamp switch.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
Test Item
Description
SEAT BELT WARN TEST
This test is able to check seat belt warning chime operation [On/Off].
LIGHT WARN ALM
This test is able to check light warning chime operation [On/Off].
REVERSE WARNING
This test is able to check reverse warning chime operation [On/Off].
ID REGIST WARNING
This test is able to check TPMS sensor ID regist warning chime operation [On/Off].
Monitor Item [Unit]
Description
TAIL LAMP SW [On/Off]
Indicates condition of combination switch.
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH.
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-35
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000010505176
WORK SUPPORT
*
1
: Factory setting
*
2
: With spicy illumination
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test Item
Description
SEAT BELT WARN TEST
This test is able to check seat belt warning chime operation [On/Off].
LIGHT WARN ALM
This test is able to check light warning chime operation [On/Off].
REVERSE WARNING
This test is able to check reverse warning chime operation [On/Off].
ID REGIST WARNING
This test is able to check TPMS sensor ID regist warning chime operation [On/Off].
Service item
Setting item
Setting
SET I/L D-UNLCK INTCON
On*
1
With interior room lamp timer function
Off
Without interior room lamp timer function
FOG LAMP OVERRIDE
On*
1
With front fog override function
Off
Without front fog override function
SPICY BRIGHTNESS SETTING*
2
MODE1
Turns spicy illumination function OFF
MODE2
Sets spicy illumination brightness.
MODE3
MODE4
MODE5*
1
MODE6
MODE7
MODE8
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
BCS-36
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (LED Headlamp)
INFOID:0000000010505169
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
CDL LOCK SW
[On/Off]
Indicated [On/Off] condition of lock signal from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door lock and unlock switch
KEY CYL LK-SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
KEY SW
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
On
Outputs interior room lamp control signal.
Off
Stops interior room lamp control signal.
Service item
Setting item
Setting
CUSTOM A/LIGHT SETTING
MODE 1*
Normal
MODE 2
More sensitive setting than normal setting. (Turns ON earlier than normal op-
eration.)
MODE 3
More sensitive setting than MODE 2. (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting. (Turns ON later than normal oper-
ation.)
TWILIGHT On
MODE 1
NOTE:
This item is displayed, but cannot be used.
MODE 2
WIPER LINK
MODE 1
NOTE:
This item is displayed, but cannot be used.
MODE 2
MODE 3
MODE 4
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-37
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: For models without rear fog lamp, this item is displayed, but cannot be monitored.
ACTIVE TEST
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
Indicates [STOP/STALL/CRANK/RUN] condition of engine states
VEH SPEED 1
[km/h]
Indicates [km/h] condition of vehicle speed signal from combination meter
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEADLAMP SW
[On/Off]
LIGHT OFF SW
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW*
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
NOTE:
This item is displayed, but cannot be monitored.
OPTI SEN (FILT)
[V]
NOTE:
This item is displayed, but cannot be monitored.
OPTICAL SENSOR
[On/Off/NG]
The sensor condition received from light & rain sensor
Test item
Operation
Description
FR FOG LAMP
On
Transmits the front fog light request signal to IPDM E/R using CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog light request signal transmission.
BCS-38
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*: For models without rear fog lamp, this item is displayed, but cannot be tested.
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (Halogen Headlamp)
INFOID:0000000010505171
WORK SUPPORT
*
1
: For models without auto light system, this item is displayed, but cannot be used.
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
RR FOG LAMP*
On
Outputs voltage to turn the rear fog lamp ON.
Off
Stops the voltage to turn the rear fog lamp OFF.
STOP LAMP 1
On
Outputs voltage to turn the stop lamp RH ON.
Off
Stops the voltage to turn the stop lamp RH OFF.
STOP LAMP 2
On
Outputs voltage to turn the stop lamp LH ON.
Off
Stops the voltage to turn the stop lamp LH OFF.
STOP LAMP 3
On
Outputs voltage to turn the high-mounted stop lamp ON.
Off
Stops the voltage to turn the high-mounted stop lamp OFF.
Test item
Operation
Description
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
2
Normal
MODE 2
More sensitive setting than normal setting. (Turns ON earlier than normal op-
eration.)
MODE 3
More sensitive setting than MODE 2. (Turns ON earlier than MODE 2.)
MODE 4
Less sensitive setting than normal setting. (Turns ON later than normal oper-
ation.)
TWILIGHT On
MODE 1
NOTE:
This item is displayed, but cannot be used.
MODE 2
WIPER LINK
MODE 1
NOTE:
This item is displayed, but cannot be used.
MODE 2
MODE 3
MODE 4
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
Indicates [STOP/STALL/CRANK/RUN] condition of engine states
VEH SPEED 1
[km/h]
Indicates [km/h] condition of vehicle speed signal from combination meter
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-39
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without auto light system, this item is displayed, but cannot be monitored.
*
2
: For models without front fog lamp, this item is displayed, but cannot be monitored.
*
3
: For models without rear fog lamp, this item is displayed, but cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEADLAMP SW
[On/Off]
LIGHT OFF SW
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
RR FOG SW*
3
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
NOTE:
This item is displayed, but cannot be monitored.
OPTI SEN (FILT)
[V]
NOTE:
This item is displayed, but cannot be monitored.
OPTICAL SENSOR*
1
[On/Off/NG]
The sensor condition received from light & rain sensor
Monitor item
[Unit]
Description
Test item
Operation
Description
FR FOG LAMP*
1
On
Transmits the front fog light request signal to IPDM E/R using CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog light request signal transmission.
RR FOG LAMP*
2
On
Outputs voltage to turn the rear fog lamp ON.
Off
Stops the voltage to turn the rear fog lamp OFF.
STOP LAMP 1
On
Outputs voltage to turn the stop lamp RH ON.
Off
Stops the voltage to turn the stop lamp RH OFF.
BCS-40
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: For models with front fog lamp, this item is displayed, but cannot be tested.
*
2
: For models without rear fog lamp, this item is displayed, but cannot be tested.
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000010505179
WORK SUPPORT
*
1
: For models without light & rain sensor
*
2
: For models with light & rain sensor
*
3
: Factory setting for Europe, Russia or South Africa
*
4
: Factory setting except for Europe, Russia or South Africa
*
5
: Factory setting for all destination
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
STOP LAMP 2
On
Outputs voltage to turn the stop lamp LH ON.
Off
Stops the voltage to turn the stop lamp LH OFF.
STOP LAMP 3
On
Outputs voltage to turn the high-mounted stop lamp ON.
Off
Stops the voltage to turn the high-mounted stop lamp OFF.
Test item
Operation
Description
Service item
Setting item
Description
WIPER SPEED SET-
TING*
1
On*
3
Linked with vehicle speed
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position.)
The setting of front wiper
INT operation can be
changed.
Off*
4
Not linked with vehicle speed
(Front wiper intermittent time linked with the wiper volume dial
position.)
RAIN SENSOR*
2
On*
5
Linked with light & rain sensor
(Front wiper intermittent time linked with the light & rain sensor,
vehicle speed, and wiper volume dial position)
The setting of front wiper
AUTO operation can be
changed
Off
Not linked with light & rain sensor
(Front wiper intermittent time linked with the vehicle speed and
wiper volume dial position)
FR RR DRIP
On*
5
Front wiper drop wipe and rear wiper drop wipe operation ON
The setting of drop wipe
operation can be
changed
Off
Front wiper drop wipe and rear wiper drop wipe operation OFF
REAR WIPER LINK
WITH REVERSE
SETTING
On
Rear wiper operation linked with reverse ON
The setting of rear wiper
operation linked with re-
verse can be changed
Off*
5
Rear wiper operation linked with reverse OFF
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch.
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-41
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: For models without headlamp washer switch, this item is indicated but is not used.
ACTIVE TEST
*: For models without headlamp washer, this item is indicated but is not used.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (LED Headlamp)
INFOID:0000000010505173
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function.
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Displays the status of the rear wiper stop position signal received from rear wiper motor.
H/L WSR SW*
[Off/On]
Status of headlamp washer switch judged by BCM.
RAIN SENSOR
[OFF/LOW/HIGH/SPLASH/NG]
Request signal from rain sensor detected by BCM is displayed.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Operates the front wiper HI operation.
Lo
Operates the front wiper LO operation.
INT
Operates the front wiper INT/AUTO operation.
Off
Stops the front wiper operation.
RR WIPER
On
Operates the rear wiper operation.
Off
Stops the rear wiper operation.
HEADLAMP WASHER*
On
Operates the headlamp washer operation.
Service item
Setting item
Setting
3-TIME FLASHER SETTING
On*
With 3-time flasher function
Off
Without 3-time flasher function
BCS-42
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FLASHER : CONSULT Function (BCM - FLASHER) (Halogen Headlamp)
INFOID:0000000010505174
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function.
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch.
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key or keyfob
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key or keyfob
RKE-PANIC
[On/Off]
NOTE:
This item is displayed, but cannot be monitored.
Service item
Setting item
Setting
3-TIME FLASHER SETTING
On*
With 3-time flasher function
Off
Without 3-time flasher function
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function.
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch.
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key or keyfob
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-43
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
INTELLIGENT KEY
INTELLIGENT KEY : Information
INFOID:0000000010699331
Check the vehicle type to use the service information in this section.
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)
INFOID:0000000010505217
WORK SUPPORT
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key or keyfob
RKE-PANIC
[On/Off]
NOTE:
This item is displayed, but cannot be monitored.
Monitor item
[Unit]
Description
Service information
Destination
Type 1
For Europe
With Intelligent Key and super lock
Type 2
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
With Intelligent Key, without super lock
Type 3
For Europe
Without Intelligent Key, with super lock
Type 4
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
Without Intelligent Key and super lock
Type 5
• For Australia
• For General export
With Intelligent Key, without super lock
Type 6
• For Australia
• For General export
Without Intelligent Key and super lock
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
BCS-44
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK I-KEY LOCK UN-
LOCK
Reminder function (door request switch) mode can be selected from the following with this
mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
ANSWER BACK KEYLESS LOCK
UNLOCK
Reminder function (Intelligent Key) mode can be selected from the following with this mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is indicated, but not used
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
IS STATUS - ECM
Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM
Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM
Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM
Display the starter request signal from IPDM E/R via CAN communication
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger door status
DOOR STAT-RR
Indicates [LOCK/READY/UNLK] condition of rear door RH status
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-45
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DOOR STAT-RL
Indicates [LOCK/READY/UNLK] condition of rear door LH status
BK DOOR STATE
NOTE:
This item is displayed, but cannot be monitored
ID OK FLAG
Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possible
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
I-KEY OK FLAG
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
vehicle
PRBT ENG STRT
Indicates whether or not the engine is in start prohibited status
ID AUTHENT CANCEL TIMER
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
unnecessary
ACC BATTERY SAVER
Indicates [On/Off] whether or not ignition battery saver is in operation
CRNK PRBT TMR
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
function operation
AUT CRANK TMR
Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME
Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR
Indicates the time that AUTO CRANKING MODE operates
CRANKING TME
Indicates the cranking operation time
SHORT CRANK
NOTE:
This item is displayed, but not used
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION
Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1
Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2
Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT
Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK
Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER
Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ
Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN)
Indicates [On/Off] condition of CAN communication
S/L POWER ERROR
Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L)
Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L)
Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L)
Indicates [On/Off] condition of engine running
S/L ID DISCORD
Indicates [Correct/Incorrect] condition of ID verification
S/L ANTI-SCAN MODE
Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT
Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN)
Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN)
Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN)
Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN)
Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN)
Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN)
Indicates [Malf/No malf] condition of hi-level malfunction
Monitor Item
Condition
BCS-46
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L OPERATION PRHBT (SPD)
Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR)
Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN)
Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN)
Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN)
Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN)
Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW
Indicates [On/Off] condition of stop/start off switch
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE PBD
NOTE:
This item is displayed, but cannot be monitored
KEY SW
NOTE:
This item is displayed, but cannot be monitored
IGN SW
NOTE:
This item is displayed, but cannot be monitored
START SW
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is
touched
• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is
touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON:[ Intelligent key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
NOTE:
This item is displayed, but cannot be used
IGN CONT2
This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation
MIRROR +5
NOTE:
This item is displayed, but cannot be used
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-47
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 2)
INFOID:0000000010505216
WORK SUPPORT
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
ENGINE START REQUEST
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation
IGNITION RELAY
NOTE:
This item is displayed, but cannot be used
STARTER CUT RELAY
This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation
ENGINE START
NOTE:
This item is displayed, but cannot be used
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation
Back door opener actuator opens when “Open” on CONSULT screen is touched
RETRACTABLE MIRROR
NOTE:
This item is displayed, but cannot be used
REVERSE LAMP TEST
NOTE:
This item is displayed, but cannot be used
KEYFOB P/W TEST
NOTE:
This item is displayed, but cannot be used
AUTO ACC 2
This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be used
AUTO ACC 1
This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation
TRUNK/LUGGAGE LAMP
TEST
This test is able to check trunk room lamp operation
• On: Operates
• Off: Non-operation
Test item
Description
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
BCS-48
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
SHORT CRANKING OUTPUT
NOTE:
This item is displayed, but cannot be monitored
IGN/ACC BATTERY SAVER
Ignition battery saver system mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANSWER BACK
NOTE:
This item is displayed, but cannot be used
ANSWER BACK I-KEY LOCK UN-
LOCK
Reminder function (door request switch) mode can be selected from the following with this
mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
ANSWER BACK KEYLESS LOCK
UNLOCK
Reminder function (Intelligent Key) mode can be selected from the following with this mode
• On: hazard warning lamp operate
• Off: hazard warning lamp operate
WELCOME LIGHT OP SET
NOTE:
This item is indicated, but not used
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
START CLUTCH SW
Indicates [On/Off] condition of clutch pedal position switch
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
NEUTRAL SW - IPDM
Indicates [On/Off] condition of park/neutral position switch
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
STARTER RELAY - IPDM
Indicates [On/Off] condition of starter relay
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
ST/INHIRELAY-IPDM
Display the starter relay/starter control relay status signal from IPDM E/R via CAN communica-
tion
REVERSE SIGNAL - IPDM
Indicates [On/Off] condition of R position
CRANKING PERMIT - ECM
Display the engine cranking permit signal from ECM via CAN communication
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст