Nissan Rogue. Manual — part 1201
TM-176
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
MAIN POWER SUPPLY AND GROUND CIRCUIT
5.
CHECK CIRCUIT BETWEEN IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector terminal and TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
DETECT MALFUNCTIONING ITEMS (PART 2)
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram — Ignition Power Supply —"
• Short circuit in harness between IPDM E/R harness connector terminal 70 and TCM harness connector ter-
minals 47, and 48.
• 10A fuse (No.46, located in the IPDM E/R). Refer to
PG-68, "IPDM E/R Terminal Arrangement"
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F35
70
F75
47
Existed
48
OVERDRIVE CONTROL SWITCH
TM-177
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OVERDRIVE CONTROL SWITCH
Component Function Check
INFOID:0000000011279396
1.
CHECK O/D OFF INDICATOR LAMP FUNCTION
Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES
>> GO TO 2.
NO
>> Go to
2.
CHECK OVERDRIVE CONTROL SWITCH FUNCTION
1. Shift the selector lever to “D” position.
2. Check that O/D OFF indicator lamp turns ON/OFF when overdrive control switch is operated.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000011279397
1.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK CVT SHIFT SELECTOR CIRCUIT
Check continuity between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 3.
3.
CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to
TM-178, "Component Inspection"
.
Is the inspection result normal?
YES
>> Repair CVT shift selector assembly. Refer to
TM-193, "Removal and Installation"
.
NO
>> Replace selector lever knob. Refer to
TM-193, "Removal and Installation"
4.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
CVT shift selector
Voltage
(Approx.)
Connector
+
−
Terminal
M107
1
2
5.0 V
CVT shift selector
Condition
Continuity
Terminal
1 – 2
Overdrive control switch is depressed.
Existed
Overdrive control switch is released.
Not existed
TM-178
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
OVERDRIVE CONTROL SWITCH
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts.
5.
CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between CVT shift selector harness connector terminal and combination meter harness
connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 2)
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace malfunctioning parts.
7.
CHECK COMBINATION METER INPUT/OUTPUT SIGNAL
1. Connect all of disconnected connectors.
2. Turn ignition switch ON.
3. Select “Data Monitor” in “METER/M&A”.
4. Select “O/D OFF SW”.
5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace combination meter. Refer to
MWI-84, "Removal and Installation"
Component Inspection
INFOID:0000000011279398
1.
CHECK OVERDRIVE CONTROL SWITCH
CVT shift selector
—
Continuity
Connector
Terminal
M107
2
Ground
Existed
CVT shift selector
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
M107
1
M76
10
Existed
CVT shift selector
—
Continuity
Connector
Terminal
M107
1
Ground
Not existed
OVERDRIVE CONTROL SWITCH
TM-179
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Check continuity between wires of shift selector knob .
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift selector knob. Refer to
.
Condition
Continuity
Overdrive control switch is de-
pressed.
Existed
Overdrive control switch is re-
leased.
Not existed
JSDIA2795ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст