Nissan Rogue. Manual — part 1193
TM-144
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0841 TRANSMISSION FLUID PRESSURE SEN/SW A
P0841 TRANSMISSION FLUID PRESSURE SEN/SW A
DTC Description
INFOID:0000000011279363
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Secondary pressure sensor circuit is open or shorted)
• Harness or connector (Primary pressure sensor circuit is open or shorted)
• Secondary pressure sensor
FAIL-SAFE
Not changed from normal driving
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.
PREPARATION BEFORE WORK
If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
1. Start the engine.
2. Drive the vehicle.
3. Maintain the following condition for 10 seconds or more.
CAUTION:
Also keep the accelerator pedal position constant.
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P0841” detected?
YES
>> Go to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000011279364
1.
REPLACE TRANSAXLE ASSEMBLY
Replace transaxle assembly. Refer to
TM-220, "Removal and Installation"
.
>> WORK END
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0841
FLUID PRESS SEN/SW A
(Transmission Fluid Pressure Sensor/Switch
“A” Circuit Range/Performance)
When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
• TCM power supply voltage: More than 11 V
• DTC other than the applicable DTC is not detected.
• Primary pulley speed: 300 rpm or more
• Secondary pulley speed: 250 rpm or more
• Target speed for shifting: Less than 0.1 seconds
• Primary pulley pressure is outside the specified value.
Selector lever
: “D” position
Vehicle speed
: Constant speed of 40 km/h (25 MPH)
P0847 TRANSMISSION FLUID PRESSURE SEN/SW B
TM-145
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0847 TRANSMISSION FLUID PRESSURE SEN/SW B
DTC Description
INFOID:0000000011279365
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Secondary pressure sensor circuit is open or shorted to ground)
• Secondary pressure sensor
• Control valve assembly
FAIL-SAFE
Not changed from normal driving
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Maintain the following conditions for 10 seconds or more.
5. Check the first trip DTC.
With GST
1. Start the engine and wait for at least 10 seconds.
CAUTION:
When the ambient temperature is less than
−20°C (−4°F) and the engine is cold, warm up the
engine for approximately 5 minutes.
2. Check the first trip DTC.
Is “P0847”detected?
YES
>> Go to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000011279366
1.
CHECK TCM INPUT SIGNALS
1. Turn ignition switch OFF.
2. Start the engine.
3. Check voltage between TCM harness connector terminals.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0847
FLUID PRESS SEN/SW B
(Transmission Fluid Pressure Sensor/Switch B
Circuit Low)
When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
• CVT fluid temperature: More than
−20°C (−4°F)
• TCM power supply voltage: 11 V or more
• Secondary pressure sensor voltage: 0.09 V or less
FLUID TEMP
:
−20°C (−4°F)
TM-146
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
P0847 TRANSMISSION FLUID PRESSURE SEN/SW B
Is the inspection result normal?
YES >> INSPECTION
END
NO
>> GO TO 2.
2.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit connector.
3. Check continuity between TCM harness connector terminals and CVT unit harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES >> There is malfunction of secondary pressure sensor. Replace transaxle assembly. Refer to
220, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
+
−
Condition
Voltage
TCM
Connector
Terminal
F75
16
Ground
• After engine warm up
• Selector lever: “N” position
• At idle
1.23 – 1.25 V
TCM
CVT unit
Continuity
Connector
Terminal
Connector
Terminal
F75
11
F74
18
Existed
16
14
26
22
TCM
—
Continuity
Connector
Terminal
F75
16
Ground
Not existed
26
P0848 TRANSMISSION FLUID PRESSURE SEN/SW B
TM-147
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0848 TRANSMISSION FLUID PRESSURE SEN/SW B
DTC Description
INFOID:0000000011279367
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector (Secondary pressure sensor circuit is shorted to power supply)
• Secondary pressure sensor
• Control valve assembly
FAIL-SAFE
Not changed from normal driving
DTC CONFIRMATION PROCEDURE
1.
PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, the ignition switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Maintain the following conditions for 10 seconds or more.
5. Check the first trip DTC.
With GST
1. Start the engine and wait for at least 10 seconds.
CAUTION:
When the ambient temperature is less than
−20°C (−4°F) and the engine is cold, warm up the
engine for approximately 5 minutes.
2. Check the first trip DTC.
Is “P0848”detected?
YES
>> Go to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000011279368
1.
CHECK TCM INPUT SIGNALS
1. Turn ignition switch OFF.
2. Start the engine.
3. Check voltage between TCM harness connector terminals.
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0848
FLUID PRESS SEN/SW B
(Transmission Fluid Pressure Sensor/Switch B
Circuit Low)
When all of the following conditions are satisfied and this state is main-
tained for 5 seconds:
• CVT fluid temperature: More than
−20°C (−4°F)
• TCM power supply voltage: More than 11 V
• Instruction secondary pressure: 5.7 MPa or less
• Secondary pressure sensor voltage: 4.7 V or more
FLUID TEMP
: More than
−20°C (−4°F)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст