Nissan Rogue. Manual — part 135
BR-10
< BASIC INSPECTION >
BRAKE BOOSTER
BRAKE BOOSTER
Inspection
INFOID:0000000011279862
Operation
Depress the brake pedal several times at five second intervals with
the engine stopped. Start the engine with the brake pedal fully
depressed. Check that the clearance between brake pedal and dash
lower panel decreases.
NOTE:
A slight impact with a small click may be felt on the pedal when the
brake pedal is fully depressed. This is normal brake system opera-
tion.
Vacuum Inspection
Idle the engine for one minute to apply vacuum to the brake booster.
Stop the engine. Depress the brake pedal several times at five sec-
ond intervals until the accumulated vacuum is released to atmo-
spheric pressure. Check that the clearance between brake pedal
and dash lower panel gradually increases (A
→ B → C) each time
the brake pedal is depressed during this operation.
Depress the brake pedal with the engine running. Then stop the
engine while holding down the brake pedal. Check that the brake
pedal stroke does not change after holding down the brake pedal for
30 seconds or more.
NOTE:
A slight impact with a small click may be felt on the pedal when the
brake pedal is fully depressed. This is normal brake system opera-
tion.
BRA0037D
JPFIA0043ZZ
JPFIA0044ZZ
FRONT DISC BRAKE
BR-11
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT DISC BRAKE
BRAKE PAD
BRAKE PAD : Inspection
INFOID:0000000011279863
Check brake pad wear thickness from an inspection hole (A) on cyl-
inder body. Check using a scale if necessary.
DISC BRAKE ROTOR
DISC BRAKE ROTOR : Inspection
INFOID:0000000011279864
APPEARANCE
Check surface of disc brake rotor for uneven wear, cracks or damage. Replace if any abnormal conditions
exist.
RUNOUT
1. Check the wheel bearing axial end play before the inspection. Refer to
(AWD).
2. Secure the disc brake rotor to the wheel hub and bearing with
wheel nuts at two wheel nut locations.
3. Measure the runout using a dial gauge 10 mm (0.39 in) from the
disc brake rotor edge.
4. Find the installation position with a minimum runout by shifting
the disc brake rotor-to-wheel hub and bearing installation posi-
tion by one hole at a time if the runout exceeds the limit value.
5. Refinish the disc brake rotor if the runout is outside the limit
even after performing the above operation. When refinishing,
use Tool.
CAUTION:
• Check in advance that the thickness of the disc brake rotor is wear thickness + 0.3 mm (0.012 in)
or more.
• If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor.
THICKNESS
Wear thickness
: Refer to
.
AWFIA0891ZZ
Runout
: Refer to
Tool number
: 38-PFM92 ( — )
Wear thickness
: Refer to
.
SBR019B
BR-12
< BASIC INSPECTION >
FRONT DISC BRAKE
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the wear limit.
Wear thickness
: Refer to
Thickness variation : Refer to
SBR020B
REAR DISC BRAKE
BR-13
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DISC BRAKE
BRAKE PAD
BRAKE PAD : Inspection
INFOID:0000000011279865
INSPECTION
Check brake pad wear thickness from an inspection hole (A) on cyl-
inder body. Check using a scale if necessary.
DISC BRAKE ROTOR
DISC BRAKE ROTOR : Inspection
INFOID:0000000011279866
Appearance
Check surface of disc brake rotor for uneven wear, cracks or damage. Replace if any abnormal conditions
exist.
Runout
1. Check the wheel bearing axial end play before the inspection. Refer to
(AWD).
2. Secure the disc brake rotor to the wheel hub and bearing with
wheel nuts at two wheel nut locations.
3. Measure the runout using a dial gauge 10 mm (0.39 in) from the
disc brake rotor edge.
4. Find the installation position with a minimum runout by shifting
the disc brake rotor-to-wheel hub and bearing installation posi-
tion by one hole at a time if the runout exceeds the limit value.
5. Refinish the disc brake rotor if the runout is outside the limit
even after performing the above operation. When refinishing, use Tool.
CAUTION:
• Check in advance that the thickness of the disc brake rotor is wear thickness + 0.3 mm (0.012 in)
or more.
• If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc brake rotor.
Thickness
Wear thickness
: Refer to
.
ALFIA0226ZZ
Runout
: Refer to
.
Tool number
: 38-PFM92 ( — )
Wear thickness
: Refer to
.
SBR019B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст