Nissan Rogue. Manual — part 136
BR-14
< BASIC INSPECTION >
REAR DISC BRAKE
Check the thickness of the disc brake rotor using a micrometer.
Replace the disc brake rotor if the thickness is below the minimum
thickness.
Wear thickness
: Refer to
.
Thickness variation
: Refer to
.
SBR020B
BRAKE PEDAL
BR-15
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
PERIODIC MAINTENANCE
BRAKE PEDAL
Adjustment
INFOID:0000000011279867
BRAKE PEDAL HEIGHT
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
2. Disconnect the harness connectors from the stop lamp switch and brake pedal position switch.
3. Turn the stop lamp switch and brake pedal position switch 45
° counterclockwise.
4. Check that the brake pedal height meets the specification by checking the brake pedal and brake booster
for damage and replace parts as necessary. Refer to
.
5. Turn the stop lamp switch and brake pedal position switch 45
° clockwise.
6. Connect the harness connectors to the stop lamp switch and brake pedal position switch.
7. Check the brake pedal for smooth operation.
CAUTION:
The stop lamp must turn off when the brake pedal is released.
8. Install the instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
STOP LAMP SWITCH AND BRAKE PEDAL POSITION SWITCH
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
2. Disconnect the harness connectors from the stop lamp switch and brake pedal position switch.
3. Turn the stop lamp switch and brake pedal position switch 45
° counterclockwise.
4. With the threaded ends of the stop lamp switch (3) and brake
pedal position switch (1) contacting the brake pedal stopper
bracket (2), turn the switches 45
° clockwise to lock in place.
Check that both the stop lamp switch (3) and brake pedal posi-
tion switch (1) contact ends to brake pedal stopper bracket (2)
clearance (A) are within specification.
CAUTION:
• Make sure that the clearance (A) between the brake pedal
stopper bracket (2), stop lamp switch (3) and the brake
pedal position switch (1) contact ends are within specifi-
cation.
• The stop lamp must turn off when the brake pedal is
released.
5. Connect the harness connector to the stop lamp switch and the brake pedal position switch.
6. Install instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
Clearance (A) : Refer to
ALFIA0441ZZ
BR-16
< PERIODIC MAINTENANCE >
BRAKE FLUID
BRAKE FLUID
Drain and Refill
INFOID:0000000011279868
CAUTION:
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may damage paint. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Prior to repair, turn the ignition switch OFF, disconnect the ABS actuator and electric unit (control
unit) connector or negative battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
• Refill brake system with new brake fluid. Refer to
MA-11, "Fluids and Lubricants"
• Do not reuse drained brake fluid.
DRAINING
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector or nega-
tive battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
2. Connect a vinyl tube to bleeder valve.
3. Depress brake pedal, loosen bleeder valve, and gradually
remove brake fluid.
CAUTION:
Do not allow reservoir tank to empty as this may cause
damage to master cylinder internal components.
REFILLING
1. Make sure no foreign material is in the reservoir tank, and refill
with new brake fluid.
CAUTION:
Do not reuse drained brake fluid.
2. Refill the brake system as follows:
• Depress the brake pedal.
• Loosen bleeder valve.
• Slowly depress brake pedal to 2/3 of the brake pedal full
stroke.
• Tighten bleeder valve.
• Release brake pedal.
Repeat this operation at intervals of two or three seconds until
all old brake fluid is discharged. Add new brake fluid frequently.
CAUTION:
Do not allow reservoir tank to empty as this may cause damage to master cylinder internal compo-
nents.
3. Bleed the air out of the brake hydraulic system. Refer to
BR-16, "Bleeding Brake System"
.
Bleeding Brake System
INFOID:0000000011279869
CAUTION:
• While bleeding, pay attention to the brake fluid level.
• Do not allow reservoir tank to empty as this may cause damage to master cylinder internal compo-
nents.
• Before working, disconnect ABS actuator and electric unit (control unit) connectors or negative bat-
tery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
1. Turn ignition switch OFF and disconnect ABS actuator and electric unit (control unit) connector or nega-
tive battery terminal. Refer to
PG-78, "Removal and Installation (Battery)"
.
2. Connect a vinyl tube to front (RH) brake caliper bleeder valve.
3. Fully depress brake pedal 4 or 5 times.
BRA0007D
PFIA0403J
BRAKE FLUID
BR-17
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
4. With brake pedal depressed, loosen bleeder valve to bleed air in brake line, and then tighten it immedi-
ately.
5. Repeat steps 3 and 4 until all of the air is out of the brake line.
6. Tighten the bleeder valve to the specified torque. Refer to
BR-49, "BRAKE CALIPER ASSEMBLY (1 PIS-
(rear disc brake).
7. Repeat steps 2 through 6, with the reservoir tank filled at least halfway. Bleed the air in the following order:
front (RH), front (LH), rear (RH), rear (LH).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст