Nissan Rogue. Manual — part 1021
RF-64
< UNIT DISASSEMBLY AND ASSEMBLY >
PANORAMIC ROOF GLASS
Handle panoramic roof glass with care to prevent damage.
DISASSEMBLY
1. Remove moonroof unit assembly. Refer to
RF-58, "Removal and Installation"
.
2. Remove four screws and panoramic roof glass.
ASSEMBLY
Installation is in the reverse order of removal.
CAUTION:
• First tighten left front screw, then right rear screw to prevent uneven alignment then tighten remain-
ing screws.
• After installing panoramic roof glass, check gap/height adjustments and operation. Refer to
.
SUNSHADE
RF-65
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SUNSHADE
Disassembly and Assembly
INFOID:0000000011583513
CAUTION:
• Do not rotate sunshade retainer and moonroof unit bases or damage to components may occur.
• Do not over tighten screws on the moonroof unit bases or damage may occur.
DISASSEMBLY
1. Open the sunshade leaving eight inches showing.
2. Remove panoramic roof glass. Refer to
RF-63, "Disassembly and Assembly"
3. Release sunshade retainer (2) from sunshade retainer couplings
(1) (LH/RH).
a. Release the sunshade retainer from both couplings (LH/RH) by
pulling rearward as shown.
b. Rotate the sunshade retainer 90 degrees as shown.
c. Pull back the sunshade retainer (2) to remove ends from each
sunshade coupling (1) (LH/RH).
4. Using a suitable tool, press up on the sunshade spacer (2)
located between the sunshade (1) and moonroof unit bases.
5. Remove sunshade (1) by applying pressure toward the drivers
side and pulling rearward from the moonroof bases.
6. Remove moonroof unit base screws (A).
7. Disassemble by pulling off both moonroof unit bases (LH/RH)
from the moonroof unit tracks.
AWJIA1644ZZ
AWJIA1640ZZ
AWBIA2347ZZ
AWJIA1647ZZ
RF-66
< UNIT DISASSEMBLY AND ASSEMBLY >
SUNSHADE
8. Manually disengage the sunshade motor and moonroof motor assembly using a suitable tool then remove
both sunshade cables and glass lid cables by pulling rearward.
9. Remove the cable guides (LH/RH) by pulling rearward from the moonroof unit tracks.
ASSEMBLY
CAUTION:
Do not remove the sunshade retainer pin or damage may occur.
1. Insert the sunshade and glass lid cables guides by sliding forward on the moonroof unit track.
2. Assembly moonroof unit bases (2) (LH/RH) by pushing forward
on the moonroof unit tracks (1) (LH/RH).
NOTE:
RH side shown; LH similar.
3. Insert sunshade black hem over lower guide (3) and under
upper guide (2) on the moonroof unit bases (1) (LH/RH).
(1) Sunshade black hem.
(2) Sunshade fabric.
4. Assemble the sunshade by applying pressure towards the drivers and inserting both ends into the moon-
roof unit bases (LH/RH).
AWBIA2351ZZ
AWJIA1641ZZ
AWBIA2352ZZ
SUNSHADE
RF-67
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
5. Assemble sunshade retainer.
a. Position the sunshade retainer on the backside of the moonroof
unit couplings then position the moonroof unit couplings inside
the sunshade stays open channel.
b. Rotate the sunshade 90 degrees.
c. Snap in place both ends of the sunshade stay on both LH/RH
sunshade couplings.
6. Manually engage the sunshade motor and moonroof motor assembly using a suitable tool
7. With the sunshade (2) assembled remove the sunshade spring
retainer pin (1).
8. Install sunshade spacer (2) between sunshade (1) and moon-
roof unit base..
9. Install panoramic roof glass. Refer to
RF-63, "Disassembly and Assembly"
10. Install moonroof unit assembly. Refer to
RF-58, "Removal and Installation"
AWJIA1642ZZ
AWBIA2350ZZ
AWBIA2347ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст