Nissan Rogue. Manual — part 816
HEADLINING
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Exploded View
INFOID:0000000011277487
WITHOUT MOONROOF
AWJIA1326ZZ
1.
Map lamp assembly bracket
2.
Headlining
3.
Assist grip (without coat hanger)
4.
Map lamp assembly
5.
Sun visor holder (LH/RH)
6.
Sun visor (RH)
7.
Sun visor cover
8.
Sun visor (LH)
9.
Assist grip (with coat hanger)
10. Headlining cover
11. Top tether strap child restraint finisher
Front
Pawl
INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
WITH MOONROOF
Removal and Installation
INFOID:0000000011277488
REMOVAL
WARNING:
Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at
least three minutes.
1. Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove front pillar finisher (LH/RH). Refer to
INT-20, "FRONT PILLAR FINISHER : Removal and Installa-
3. Remove center pillar upper finisher (LH/RH). Refer to
INT-21, "CENTER PILLAR UPPER FINISHER :
.
4. Remove luggage side upper finisher (LH/RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER :
.
5. Remove map lamp assembly. Refer to
INL-55, "Removal and Installation"
6. Disconnect personal lamp and microphone harness connectors.
AWJIA1547ZZ
1.
Headlining
2.
Front assist grip bracket (LH)
3.
Map lamp assembly bracket
4.
Front assist grip bracket (RH)
5.
Assist grip (with coat hanger)
6.
Map lamp assembly
7.
Assist grip (without coat hanger)
8.
Sun visor holder (LH/RH)
9.
Sun visor (RH)
10. Sun visor cover (LH/RH)
11. Sun visor (LH)
12. Headlining cover
13. Top tether strap child restraint finisher
Front
Pawl
HEADLINING
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
7. Remove sun visor cover (LH/RH) (1) by inserting a suitable tool
(A) as shown.
: Pawl
CAUTION:
Do not damage headlining or sun visor cover surface.
8. Remove sun visor bolts (A) (LH/RH), then disconnect harness
connectors and remove .
9. Insert a suitable tool (A) at approximately a 30 degree angle into
the sun visor holder notch on the front of the sun visor holder
(1). Press in to release the locking tab (B). While holding in lock-
ing tab (B), turn the sun visor holder (1) 90 degrees to release it
from the headliner.
• If the sun visor holder (1) does not fully rotate, make sure that
the suitable tool (A) is pressing in on the locking tab (B) and is
not positioned under locking tab (B). Reinsert the suitable tool
(A) as necessary to release the locking tab (B).
•
: Front
CAUTION:
Do not force the sun visor holder when removing as the
locking tab may be damaged if the suitable tool is not posi-
tioned correctly.
10. Remove front assist grip (LH/RH) and rear assist grip (LH/RH).
a. Remove assist grip cap (3).
b. Release clip (1) and remove assist grip (2).
AWBIA1997ZZ
ALJIA1362ZZ
ALJIA0537ZZ
AWBIA1994ZZ
INT-32
< REMOVAL AND INSTALLATION >
HEADLINING
11. Insert suitable tool from front, release pawls then pull headlining
cover (LH/RH) (1) forward and outward to remove.
: Pawl
Front
12. Insert two fingers through hole on headlining.
13. Release tether (A) from hook (B) and remove.
14. Remove screw (A) then release pawls using a suitable tool and
remove child tether finisher (1).
: Pawl
15. Release headlining clips at rear and remove headlining through the back door.
CAUTION:
• When removing headlining, two workers are required.
• Do not bend headlining when removing.
• Be careful not to scratch or damage any part of the body while removing the headlining.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install sun-visor holder (LH/RH) and headlining clips at rear for positioning.
• Do not to bend the headlining when installing.
ALJIA1380ZZ
(A)
:Tether
ALJIA1476ZZ
ALJIA1477ZZ
AWJIA1287ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст