Nissan Rogue. Manual — part 668
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000011280028
REMOVAL
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
1. Remove front grille. Refer to
EXT-23, "Removal and Installation"
2. Remove front bumper fascia clips (A).
3. Remove front bumper fascia clips (A) and screws (B).
(1): Engine under cover
4. Remove front air spoiler. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
5. Remove engine side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
6. Partially remove front fender protectors (LH/RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded
.
7. Partially remove front over fender (LH/RH). Refer to
EXT-30, "FRONT OVER FENDER : Exploded View"
8. Remove front bumper fascia screws (A) (LH/RH).
(1): Front bumper fascia
(2): Front over fender
9. Disconnect fog lamp harness connectors (LH/RH) (if equipped).
10. Release front bumper fascia pawls from front bumper fascia side brackets (LH/RH) and remove.
CAUTION:
When removing front bumper fascia, two people are required to avoid damaging.
ALKIA3340ZZ
AWKIA3213ZZ
ALKIA3344ZZ
EXT-18
< REMOVAL AND INSTALLATION >
FRONT BUMPER
11. Remove front bumper fascia bolts (A) and the front bumper side
bracket (1) (LH/RH) (if necessary).
12. Remove intelligent key warning buzzer. Refer to
DLK-280, "Removal and Installation"
.
13. Remove the front energy absorber.
14. Release harness connector clips from bumper reinforcement,
then remove bumper reinforcement nuts (A) and bumper rein-
forcement (1) (LH/RH).
15. Remove front bumper reinforcement support bolts (A) and front
bumper reinforcement supports (1) (LH/RH).
16. Remove the following parts (if necessary) after removing front bumper fascia assembly.
• Front fog lamps (if equipped). Refer to
EXL-121, "Removal and Installation"
• Front fog lamp finishers.
• Front fascia grille.
• Front license plate bracket.
• Tow cover.
• Front bumper chrome molding.
INSTALLATION
Installation in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
ALKIA3363ZZ
ALKIA3364ZZ
ALKIA3371ZZ
FRONT BUMPER
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Fitting adjustment cannot be performed.
mm (in)
AWKIA3212ZZ
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
6.9 (0.27)
8.9 (0.35)
10.9 (0.43)
B-B
Clearance
0.1 (0.004)
1.5 (0.06)
3.0 (0.12)
C-C
Clearance
0.1 (0.004)
1.5 (0.06)
3.0 (0.12)
D-D
Clearance
0.1 (0.004)
1.5 (0.06)
3.0 (0.12)
E-E
Clearance
0.1 (0.004)
0.3 (0.01)
1.0 (0.04)
E-E
Surface height
-0.3 (0.01)
0.7 (0.03)
1.7 (0.07)
F-F
Clearance
0.5 (0.02)
0.5 (0.02)
1.0 (0.04)
F-F
Surface height
0.5 (0.02)
0.5 (0.02)
1.0 (0.04)
G-G
Clearance
0.5 (0.02)
1.5 (0.06)
2.5 (0.10)
H-H
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
J-J
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
J-J
Surface height
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
K-K
Clearance
0.5 (0.02)
2.0 (0.08)
3.5 (0.14)
K-K
Surface height
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
EXT-20
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded View
INFOID:0000000011280029
Removal and Installation
INFOID:0000000011280030
REMOVAL
CAUTION:
1.
Rear bumper fascia side bracket
(LH)
2.
Rear mud protector
3.
Rear bumper reinforcement sup-
port (LH)
4.
Rear bumper fascia undercover
(LH)
5.
Rear bumper reinforcement
6.
Rear energy absorber
7.
Rear bumper bracket (LH)
8.
Rear bumper fascia
9.
Rear bumper fascia reflector (LH)
10. Rear bumper finisher
11. Rear bumper fascia reflector (RH) 12. Rear bumper bracket (RH)
13. Rear bumper fascia undercover
(RH)
14. Rear bumper reinforcement sup-
port (RH)
15. Rear bumper fascia side bracket
(RH)
AWKIA2901ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст