Nissan Rogue. Manual — part 669
REAR BUMPER
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
1. Remove rear mudguard (LH/RH) (if equipped). Refer to
EXT-34, "Removal and Installation"
.
2. Partially remove rear over fender molding (LH/RH). Refer to
EXT-32, "REAR OVER FENDER : Exploded
.
3. Partially remove rear wheel house protector (LH/RH). Refer to
EXT-29, "REAR WHEEL HOUSE PRO-
.
4. Remove clips and remove rear bumper fascia undercover (LH/RH).
5. Remove rear bumper fascia upper screws (A).
6. Remove rear bumper fascia screw (A) (LH/RH).
7. Disconnect harness connector from rear sonar sensors (if equipped).
8. Release pawls (LH/RH) using a suitable tool and remove rear
bumper fascia.
: Pawl
CAUTION:
When removing rear bumper fascia, two people are
required to avoid damaging.
9. Remove energy absorber.
10. Remove bolts (A) and remove rear bumper side bracket (LH/
RH) (if necessary).
ALKIA3377ZZ
ALKIA3376ZZ
ALKIA3382ZZ
ALKIA3384ZZ
EXT-22
< REMOVAL AND INSTALLATION >
REAR BUMPER
11. Remove rear bumper reinforcement nuts (LH/RH), then remove rear bumper reinforcement (if necessary).
12. Remove bumper stay bolts, then remove bumper stay (if necessary).
13. Remove rear bumper reinforce support bolts and rear bumper reinforcement (LH/RH).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
Unit: mm (in)
AWKIA2880ZZ
Section
Measurement
Minimum
Target Value
Maximum
A-A
Clearance
6.0 (0.24)
8.0 (0.31)
10.0 (0.39)
B-B
Clearance
0.1 (0.004)
0.3 (0.01)
1.0 (0.04)
B-B
Surface height
-0.3 (0.01)
0.7 (0.03)
1.7 (0.07)
C-C
Clearance
3.0 (0.12)
5.0 (0.20)
7.0 (0.28)
C-C
Surface height
-1.8 (-0.07)
0.3 (0.01)
2.4 (0.09)
D-D
Clearance
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
E-E
Clearance (upper)
0.6 (0.02)
1.6 (0.06)
2.6 (0.10)
E-E
Clearance (lower)
0.0 (0.00)
1.0 (0.04)
2.0 (0.08)
FRONT GRILLE
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
FRONT GRILLE
Exploded View
INFOID:0000000011280031
Removal and Installation
INFOID:0000000011280032
REMOVAL
1. Remove the four front grille upper clips (A).
2. Release clips and pawls, then remove front grille.
: Clip
: Pawl
1.
Front bumper fascia
2.
Front camera (if equipped)
3.
Front grille
4.
Front emblem
Pawl
Clip
ALKIA3352ZZ
ALKIA3390ZZ
AWKIA3214ZZ
EXT-24
< REMOVAL AND INSTALLATION >
FRONT GRILLE
3. Disconnect harness connector (A) from front camera (if
equipped).
4. Remove the following parts after removing front grille (if necessary).
• Front camera (if equipped). Refer to
AV-381, "Removal and Installation"
• Front emblem.
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
Calibration must be performed after removing/replacing the front camera (if equipped). Refer to
IBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure"
.
ALKIA3394ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст