Nissan Rogue. Manual — part 340
DLK-202
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR CLOSURE MOTOR
BACK DOOR CLOSURE MOTOR
Diagnosis Procedure
INFOID:0000000011278934
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR CLOSURE MOTOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect back door lock assembly connector.
3. Check voltage between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> Replace back door lock assembly. Refer to
DLK-270, "DOOR LOCK : Removal and Installation"
NO
>> GO TO 2.
2.
CHECK BACK DOOR CLOSURE MOTOR CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and back door lock
assembly harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage
(Approx.)
Back door lock assembly
Connector
Terminal
D512
1
Ground
Back door opener
switch
Pressed
Battery voltage
2
Released
0 V
Automatic back door control module
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
B56
31
D512
1
Yes
38
2
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
31
No
38
2015 Rogue NAM
AUTOMATIC BACK DOOR WARNING BUZZER
DLK-203
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
AUTOMATIC BACK DOOR WARNING BUZZER
Diagnosis Procedure
INFOID:0000000011278935
Regarding Wiring Diagram information, refer to
.
1.
CHECK BACK DOOR WARNING CHIME POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect back door warning chime connector.
3. Check voltage between back door warning chime harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR WARNING CHIME OUTPUT SIGNAL CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and back door warning
chime harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR WARNING CHIME GROUND CIRCUIT
Check continuity between back door warning chime harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK BACK DOOR WARNING CHIME
DLK-204, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace back door warning chime. Refer to
DLK-281, "Removal and Installation"
.
(+)
(–)
Voltage
(Approx.)
Back door warning chime
Connector
Terminal
B61
1
Ground
Battery voltage
Automatic back door control module
Back door warning chime
Continuity
Connector
Terminal
Connector
Terminal
B56
37
B61
1
Yes
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
37
No
Back door warning chime
Ground
Continuity
Connector
Terminal
B61
2
Yes
2015 Rogue NAM
DLK-204
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
AUTOMATIC BACK DOOR WARNING BUZZER
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> Inspection End.
Component Inspection
INFOID:0000000011278936
1.
CHECK BACK DOOR WARNING CHIME
1. Turn ignition switch OFF.
2. Disconnect back door warning chime connector.
3. Check battery power supply directly to back door warning chime terminals and check the operation.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace back door warning chime. Refer to
DLK-281, "Removal and Installation"
.
back door warning chime
Operation
Terminal
(+)
(-)
1
2
Chime sounds
2015 Rogue NAM
INTEGRATED HOMELINK TRANSMITTER
DLK-205
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTEGRATED HOMELINK TRANSMITTER
Component Function Check
INFOID:0000000011278937
1.
CHECK FUNCTION
Check that system receiver (garage door opener, etc.) operates with original hand-held transmitter.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Receiver or hand-held transmitter is malfunctioning.
2.
CHECK ILLUMINATE
1. Turn ignition switch OFF.
2. Does red light of transmitter illuminate when any transmitter button is pressed?
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Refer to
DLK-205, "Diagnosis Procedure"
3.
CHECK TRANSMITTER
Check transmitter with Tool*.
*:For details, refer to Technical Service Bulletin.
Is the inspection result normal?
YES
>> Receiver or hand-held transmitter malfunction, not vehicle related.
NO
>> Replace auto anti-dazzling inside mirror (Homelink
®
universal transceiver). Refer to
.
Diagnosis Procedure
INFOID:0000000011278938
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect auto anti-dazzling inside mirror (Homelink
®
universal transceiver) connector.
3. Check voltage between auto anti-dazzling inside mirror (Homelink
®
universal transceiver) harness con-
nector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check the following items:
• 5A fuse 14 located in the fuse block (J/B).
• 10A fuse 30 located in the fuse block (J/B).
• Harness for open or short between fuse and auto anti-dazzling inside mirror (Homelink
®
univer-
sal transceiver).
2.
CHECK GROUND CIRCUIT
Check continuity between auto anti-dazzling inside mirror (Homelink
®
universal transceiver) harness connec-
tor and ground.
Auto anti-dazzling inside mirror
(Homelink
®
universal transceiv-
er) connector
Terminal Condition
Voltage (V)
(Approx.)
R7
10
Ground
Ignition switch position:
OFF
Battery voltage
6
Ignition switch position:
ON
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст