Nissan Rogue. Manual — part 339
DLK-198
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
TOUCH SENSOR
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK TOUCH SENSOR LH GROND CIRCUIT
1. Disconnect automatic back door control module and touch sensor LH connector.
2. Check continuity between automatic back door control module harness connector and touch sensor LH
harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TOUCH SENSOR LH GROND CIRCUIT 2
1. Connect automatic back door control module and touch sensor LH connector.
2. Check voltage between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TOUCH SENSOR LH
DLK-199, "LH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace touch sensor LH. Refer to
DLK-271, "TOUCH SENSOR : Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> Inspection End.
Automatic back door control module
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B55
2
D511
1
Yes
Automatic back door control module
Ground
Continuity
Connector
Terminal
B55
2
No
Automatic back door control module
Touch sensor LH
Continuity
Connector
Terminal
Connector
Terminal
B55
13
D511
2
Yes
Automatic back door control module
Ground
Continuity
Connector
Terminal
B55
13
No
(+)
(–)
Voltage
(Approx.)
Automatic back door control module
Connector
Terminal
B55
13
Ground
0.01 – 0 V
2015 Rogue NAM
TOUCH SENSOR
DLK-199
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
LH : Component Inspection
INFOID:0000000011278931
1.
CHECK TOUCH SENSOR LH
1. Turn ignition switch OFF.
2. Disconnect touch sensor LH connector.
3. Check resistance between touch sensor LH terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace touch sensor LH. Refer to
DLK-271, "TOUCH SENSOR : Removal and Installation"
.
Touch sensor LH
Condition
Resistance
(Approx.)
Terminal
1
2
Touch sensor LH
Detect obstruction
380 – 420 k
Ω
Other than above
0.95 – 1.05 k
Ω
2015 Rogue NAM
DLK-200
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SPINDLE MOTOR
SPINDLE MOTOR
RH
RH : Diagnosis Procedure
INFOID:0000000011278932
Regarding Wiring Diagram information, refer to
.
1.
CHECK SPINDLE MOTOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect spindle unit RH connector.
3. Check voltage between spindle unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace spindle unit RH. Refer to
DLK-270, "SPINDLE UNIT : Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK SPINDLE MOTOR CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and spindle unit har-
ness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
LH
LH : Diagnosis Procedure
INFOID:0000000011278933
Regarding Wiring Diagram information, refer to
.
1.
CHECK SPINDLE MOTOR INPUT SIGNAL
1. Turn ignition switch OFF.
(+)
(–)
Condition
Voltage
(Approx.)
Spindle unit RH
Connector
Terminal
B73
1
Ground
Back door
Auto open opera-
tion
Battery voltage
7
Auto close opera-
tion
Automatic back door control module
Spindle unit RH
Continuity
Connector
Terminal
Connector
Terminal
B56
29
B73
1
Yes
36
7
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
29
No
36
2015 Rogue NAM
SPINDLE MOTOR
DLK-201
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Disconnect spindle unit LH connector.
3. Check voltage between spindle unit LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace spindle unit LH. Refer to
DLK-270, "SPINDLE UNIT : Removal and Installation"
NO
>> GO TO 2.
2.
CHECK SPINDLE MOTOR CIRCUIT
1. Disconnect automatic back door control module connector.
2. Check continuity between automatic back door control module harness connector and spindle unit LH
harness connector.
3. Check continuity between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control module. Refer to
DLK-283, "Removal and Installation"
.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage
(Approx.)
Spindle unit LH
Connector
Terminal
B95
1
Ground
Back door
Auto open opera-
tion
Battery voltage
7
Auto close opera-
tion
Automatic back door control module
Spindle unit LH
Continuity
Connector
Terminal
Connector
Terminal
B56
27
B95
1
Yes
34
7
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
27
No
34
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст