Nissan Rogue. Manual — part 326
DLK-146
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2622 INSIDE ANTENNA
B2622 INSIDE ANTENNA
DTC Logic
INFOID:0000000011278855
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INSIDE ANT DIAGNOSIS” in “Work support”.
3. Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “Work support” of “INTELLIGENT KEY”.
4. Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
DLK-146, "Diagnosis Procedure"
.
NO
>> Inside key antenna (console) is OK.
Diagnosis Procedure
INFOID:0000000011278856
Regarding Wiring Diagram information, refer to
.
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
NO
>> GO TO 2.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2622
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (console) is sent to BCM.
• Inside key antenna (console)
• Harness or connector
[Inside key antenna (console) cir-
cuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B16
62, 63
Ground
When Intelligent Key is in the an-
tenna detection area.
When Intelligent Key is not in the
antenna detection area.
JMKIA3839GB
JMKIA5951GB
2015 Rogue NAM
B2622 INSIDE ANTENNA
DLK-147
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and inside key antenna (console) connector.
2. Check continuity between BCM harness connector and inside key antenna (console) harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1. Replace inside key antenna (console). (New antenna or other antenna)
2. Connect BCM connector and inside key antenna (console) connector.
3. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (console). Refer to
DLK-278, "CONSOLE : Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
BCM
Inside key antenna (console)
Continuity
Connector
Terminal
Connector
Terminal
B16
63
B77
1
Yes
62
2
BCM
Ground
Continuity
Connector
Terminal
B16
63
No
62
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
B16
62, 63
Ground
When Intelligent Key is in the an-
tenna detection area.
When Intelligent Key is not in the
antenna detection area.
JMKIA3839GB
JMKIA5951GB
2015 Rogue NAM
DLK-148
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
AUTOMATIC BACK DOOR CONTROL UNIT
AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000011278857
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSIBLE LINK
Check that the following fusible link is not open.
Is the fusible link open?
YES
>> Replace the open fusible link after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic back door control module connector.
3. Check voltage between automatic back door control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
Check continuity between automatic back door control module harness connector and ground.
Does continuity exist?
YES
>> Inspection End.
NO
>> Repair or replace harness.
BCM
BCM : Diagnosis Procedure
INFOID:0000000011377366
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuse is not blown.
Fusible link No.
Signal name
K (30A)
Battery power supply
(+)
(
−)
Voltage
(Approx.)
Automatic back door control module
Connector
Terminal
B56
25
Ground
Battery voltage
Automatic back door control module
Ground
Continuity
Connector
Terminal
B56
32
Yes
B55
4
B55
16
2015 Rogue NAM
POWER SUPPLY AND GROUND CIRCUIT
DLK-149
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the fuse blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connector M20.
2. Check voltage between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between BCM connector M20 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Terminal No.
Signal name
Fuse No.
161
BCM power supply
7 (10A)
BCM
Ground
Voltage
(Approx.)
Connector
Terminal
M20
161
—
Battery voltage
BCM
Ground
Continuity
Connector
Terminal
M20
170
—
Yes
171
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст