Nissan Rogue. Manual — part 84
AV-328
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
U1305 CONFIG UNFINISH
U1305 CONFIG UNFINISH
DTC Logic
INFOID:0000000011277000
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000011277001
1.
PERFORM CONFIGURATION
When U1305 is detected, perform configuration of around view monitor control unit.
>> Refer to
AV-281, "CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Pro-
CONSULT Display
DTC Detection Condition
Possible Cause
Non-completion of the configu-
ration
[U1305]
Configuration of around view monitor control unit
is incomplete.
Perform configuration of around view monitor
control unit.
AV
U1310 CONTROL UNIT (AV)
AV-329
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U1310 CONTROL UNIT (AV)
DTC Logic
INFOID:0000000011277002
DTC DETECTION LOGIC
CONSULT Display
DTC Detection Condition
Possible Cause
CONTROL UNIT (AV)
[U1310]
Error during CAN controller hardware initializa-
tion (MCAN).
Replace AV control unit if malfunction occurs
constantly.
Refer to
AV-369, "Removal and Installation"
.
AV-330
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
AV CONTROL UNIT
AV CONTROL UNIT : Diagnosis Procedure
INFOID:0000000011277003
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuses are not blown:
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect AV control unit connectors M108 and M109.
3. Check voltage between AV control unit connectors M108 and M109 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between AV control unit connector M108 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
BOSE SPEAKER AMP
BOSE SPEAKER AMP : Diagnosis Procedure
INFOID:0000000011277004
Regarding Wiring Diagram information, refer to
.
1.
CHECK FUSE
Check that the following fuses are not blown:
Terminal No.
Signal name
Fuse No.
19
Battery power supply
16 (20A)
40
Ignition power supply
30 (10A)
AV control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M108
19
—
Ignition switch: OFF
Battery voltage
M109
40
Ignition switch: ON
AV control unit
Ground
Continuity
Connector
Terminal
M108
20
—
Yes
AV
POWER SUPPLY AND GROUND CIRCUIT
AV-331
< DTC/CIRCUIT DIAGNOSIS >
[NAVIGATION WITH BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Bose speaker amp. connector B137.
3. Check voltage between Bose speaker amp. connector B137 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK GROUND CIRCUIT
Check continuity between Bose speaker amp. connector B137 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
AROUND VIEW MONITOR CONTROL UNIT
AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure
INFOID:0000000011277005
Regarding Wiring Diagram information, refer to
.
WITHOUT DRIVER ASSISTANCE SYSTEM
1.
CHECK FUSE
Check that the following fuses are not blown:
Are the fuses blown?
YES
>> Replace the blown fuse after repairing the affected circuit.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector M103.
3. Check voltage between around view monitor control unit connector M103 and ground.
Terminal No.
Signal name
Fuse No.
11
Battery power supply
11 (20A)
Bose speaker amp.
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
B137
11
—
Ignition switch: OFF
Battery voltage
Bose speaker amp.
Ground
Continuity
Connector
Terminal
B137
12
—
Yes
Terminal No.
Signal name
Fuse No.
2
Battery power supply
15 (20A)
Around view monitor control unit
Ground
Condition
Voltage
(Approx.)
Connector
Terminal
M103
2
—
Ignition switch: OFF
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст